Setup & Configuration
HDE-VoIP Telephones
Page 14
Web Page Item
Description
Volume Settings
The volume settings describe the volume set on reboot. The user can change the
volume by using the up and down arrows, but this change is temporary and the
volume will be reset when the device is rebooted.
Speaker Volume (0-9):
The speaker volume sets the default volume of the device on boot. Valid values are 0-
9. Test the speaker volume using the ‘Test Audio’ button below.
HL Gain Control (0-9)
This is used in conjunction with the optional VoIP Extender Module w/Hearing Aid
Loop amplifier. Only for units which are equipped with a Hearing Aid T-Coil Antenna.
Microphone Gain (0-9):
The microphone gain sets the initial input gain of the on board microphone. Valid
values are 0-9. Test the speaker volume using the ‘Test Microphone’ button below.
Ringer Volume (0-9):
The ringing volume that is heard on the speaker of the phone. Valid values are 0-9.
This setting is for units that use the speaker as a ringer. It will not affect units with a
fixed buzzer.
Aux Port
Activate Relay with DTMF Code:
When this option is enabled, the device will activate the relay when it receives a DTMF
code (SIP or rfc2833).
DTMF Activation Code:
This 25-character field (Digits 0-9 only) can be used to set a DTMF code used to
activate the relay.
NOTE
: the operator must press the “#” or “
✱
” key after entering the
code for it to be accepted.
DTMF Activation Duration (in
seconds):
When the relay is activated with a DTMF code, it will remain active for this duration in
seconds. Valid values are 1-9.
NOTE
: A DTMF activation of
0
will toggle the relay indefinitely or until the activation,
code is sent again.
Activate Relay During Ring
:
When this option is enabled, the relay will activate when the device has received a call
and is playing a ringtone.
Activate Relay During Night Ring
:
When this option is enabled, the relay will activate when the device has received a call
to the night ring extension.
Pulse Relay when Ringing:
On in-coming calls…When a “ring” is present the relay will pulse with a cadence of 2
seconds on, 3 seconds off.
Pulse Buzzer when Ringing:
When a “ring” is present the internal ringer will pulse with a cadence of 2 seconds on,
3 seconds off.
Activate Relay on Outgoing Ring
When enabled, once a push button is pressed, the relay will activate and remain
activated until the call is answered. Then it will deactivate unless the “Activate Relay
While Call Active” is also enabled.
Activate Relay While Call Active
:
When this option is enabled, the relay will activate when a call is established with
another SIP device. It will remain active for the duration of the call.
Expansion Module Enable
Check this feature when used with the Guardian Telecom VoIP Expansion Module.
This activates the extended relay management features.
LED1 & LED 2 Control Setup
(LED1 shown, LED2 similar)
Activate LED1 with DTMF Code:
When this option is enabled, the device will activate Output Port 1 (Generally wired to
the Emergency Button respective LED) when it receives a DTMF code (SIP or
rfc2833).
Activate LED2 with DTMF Code:
When this option is enabled, the device will activate Output Port 2 (Generally wired to
the Information or General Call Button respective LED) when it receives a DTMF code
(SIP or rfc2833).
DTMF Activation Code:
This 25-character field (Digits 0-9 only) can be used to set a DTMF code used to
activate the LED.
NOTE
: the operator must press the “#” or “
✱
”key after entering the code for it to be
accepted.
DTMF Activation Duration (in
seconds):
When the LED is activated with a DTMF code, it will remain active for this duration in
seconds. Valid values are 1-9.
NOTE
: A DTMF activation of
0
will toggle the LED state indefinitely until the activation
code is sent again.
Blink LEDn on Call, Solid while Call
Active:
Active button – LED will flash on/off during call progress and remain on once call link is
established.
Solid LEDn, Blink during ring & call
LED always on, blinks when button pressed and for duration of call.