manualshive.com logo in svg

Ciena 170-3930-900, Hardware Installation And Start-Up Manual

Share
Download
Ciena 170-3930-900 Hardware Installation And Start-Up Manual Download Page 36

2-20

   Installation

3930 Service Delivery Switch

Hardware Installation and Start-up Manual

009-3223-001   Standard    Revision E

Copyright

©

 2012-2014 Ciena

®

 Corporation

January 2014

8

Verify the power supply LEDs. The following LED indications should be 
present on the 3930:

•

PSA - Status LED is solid green, Input LED is solid green

•

PSB - Status LED is solid green, Input LED is solid green

•

PWR - solid green

Note:  

The system does not distinguish between a faulty and an unpowered 

supply. As a result, if redundant power supplies are installed, but only one 
supply is connected to a power source, the unpowered supply will cause the 
system to report an alarm state (ALRM LED solid yellow and STAT LED off). 
This alarm will be cleared when the power supply is properly initialized.

The power supplies have now been installed and the system has been 
powered on. 

Summary of Contents for 170-3930-900









































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands