manualshive.com logo in svg

Christie Vive audio LS1, User Manual

Share
Download
Christie Vive audio LS1 User Manual Download Page 20

Specification

LS1 description

LS2 description

Mid-frequency and high-frequency: 101.3
dB.

Mid-frequency and high-frequency: 102.5
dB.

Recommended
amplifier power

Low-frequency: 600-1000 W at 8 ohms.
Mid-frequency and high-frequency: 200-300
W at 6 ohms.

Low-frequency: 850-1500 W at 8 ohms.
Mid-frequency and high-frequency: 350-450
W at 8ohms.

Rated impedance

Low-frequency: 8 ohms.
Mid-frequency and high-frequency: 6 ohms.

Low-frequency: 4 ohms.
Mid-frequency and high-frequency: 8 ohms.

1

For more detailed crossover information, see Recommended Crossover Settings (P/N 020-101405-01)

(https://www.christiedigital.com).

2

Measured at 2 m on tweeter axis in simulated free field conditions. Sensitivity is calculated based on

measured SPL response averaged in 200 Hz-5 kHz range.

3

IEC refers to IEC 60268-5 standard. Maximum SPL values calculated based on sensitivity and IEC

power ratings. Continuous power handling tested using IEC60268-1 noise signal for duration of two
hours.

4

Averaged in the 500 Hz-12 kHz range, at -6 dB.

Power requirements

Learn about the power specifications.

Specification

LS1 description

LS2 description

Power handling
capacity

1

Low frequency: 600 W continuous, 1000 W
IEC long term, 1500 W IEC short term.
Mid-frequency and high-frequency: 150 W
continuous, 200 W IEC long term, 300 W
IEC short term.

Low frequency: 1200 W continuous, 2000 W
IEC long term, 3000 W IEC short term.
Mid-frequency and high-frequency: 150 W
continuous, 250 W IEC long term, 350 W
IEC short term.

1

IEC refers to IEC 60268-5 standard. Maximum SPL values calculated based on sensitivity and IEC

power ratings. Continuous power handling tested using IEC60268-1 noise signal for duration of two
hours.

Physical

Learn about the physical specifications.

Specification

LS1 description

LS2 description

Input connectors

Four position terminal barrier strip with separate low-frequency and mid/high-frequency
inputs.

Enclosure

• Vented enclosure with a tuning frequency of 32 Hz (LS1) or 28 Hz (LS2)

• 18 mm marine plywood, heavily braced for maximum structural strength and

minimum panel resonance

• Rotatable mid/high-frequency section in acoustically isolated enclosure

Specifications

Christie Vive Audio LS1/LS2 Line Source Speakers User Manual

20

020-102170-01 Rev. 1 (06-2016)

Copyright 

©

 2016 Christie Digital Systems USA Inc. All rights reserved.

Summary of Contents for Vive audio LS1























Reviews:

No comments

Brands by name

Popular brands

Load more brands