manualshive.com logo in svg

Christie Vive audio LS1, User Manual

Share
Download
Christie Vive audio LS1 User Manual Download Page 19

Specifications

Learn about the product specifications. Due to continuing research, specifications are subject to

change without notice.

Audio

Learn about the audio specifications.

Specification

LS1 description

LS2 description

System type

Four-way, bi-amp, vented enclosure.

Driver components

High-frequency: 2 x 3 in. planar ribbon
driver with Kapton diaphragms and
Neodymium magnets.
Mid-frequency: 6.5 in. cone driver with 38
mm voice coil.
Low-frequency: 15 in. paper composite cone
driver with 100 mm diameter voice coil.

High-frequency: 6 in. and 3 in. planar
ribbon drivers with Kapton diaphragms and
Neodymium magnets.
Mid-frequency: 6.5 in. paper/Kevlar cone
high efficiency Neodymium magnet driver
with 51 mm voice coil.
Low-frequency: 2 x 15 in. paper composite
cone drivers with 100 mm diameter voice
coils.

Crossover

¹

Low-frequency and mid-frequency: 350 Hz,
active via processor.
Mid-frequency and high-frequency: passive
at 2.0 kHz. Two-way high-frequency section
with frequency shading network.

Low-frequency: 350 Hz active via processor.
Mid-frequency and high-frequency: Passive
in mid- and high-frequency section with 2
kHz and 7 kHz crossover points. Two-way
high-frequency section with frequency
shading network.

Frequency response

2

30 Hz-20 kHz at -6dB

Maximum SPL

3

Low-frequency: 122.8 dB continuous, 125.0
dB IEC maximum long term, 126.8 dB IEC
maximum short term.
Mid-frequency and high-frequency: 123.1
dB continuous, 124.4 dB IEC maximum long
term, 126.1 dB IEC maximum short term.
LS1 system: 126.0 dB continuous, 127.7 dB
IEC maximum long term, 129.5 dB IEC
maximum short term.

Low-frequency: 128.8 dB continuous, 131.1
dB IEC maximum long term, 132.8 dB IEC
maximum short term.
Mid-frequency and high-frequency: 124.3
dB continuous, 126.5 dB IEC maximum long
term, 128.0 dB IEC maximum short term.
LS2 system: 130.0 dB continuous, 132.4 dB
IEC maximum long term, 134.0 dB IEC
maximum short term.

System coverage

4

100

°

 horizontal dispersion , 40

°

 vertical dispersion.

Sensitivity

1

, 1 W/1 m Low-frequency: 95.0 dB.

Low-frequency: 98.0 dB.

 

Christie Vive Audio LS1/LS2 Line Source Speakers User Manual

19

020-102170-01 Rev. 1 (06-2016)

Copyright 

©

 2016 Christie Digital Systems USA Inc. All rights reserved.

Summary of Contents for Vive audio LS1























Reviews:

No comments

Brands by name

Popular brands

Load more brands