Christie FHD552-X User Manual Download Page 44 | Manualshive

Page: 44 / 70

Christie FHD552-X User Manual Download Page 44

Operation

FHD552-X LCD Panel User Manual

44

020-000741-01 Rev. 1 (07-2014)

• Power On Delay: When powering on a video wall, this control staggers the power-on

sequence so that all monitors will not turn on at once, reducing current requirements. Select a
value of from 0 to 30 seconds (inclusive) per monitor.

• DVI Indemnity: For large matrixes using a single digital source and a DVI pass-thru cables,

setting this to On may enhance the video quality and reliability of the pass-thru signals.

• Video Wall: Use this control to enable or disable video wall mode.

When video wall is set to Yes, these additional settings are available:

• Frame: This control enables or disables frame compensation, which joins the edges of adjacent

displays in a video wall together in such a way as to compensate for the gap between them.
This causes moving objects to appear to move “behind” the gap, for better continuity of motion
across the wall:

• Matrix X: This control lets you specify the number of columns in the video wall.

• Matrix Y: This control lets you specify the number of rows in the video wall.

• Division X: This control lets you specify a display’s horizontal position (column) in a video wall.

• Division Y: This control lets you specify a display’s vertical position (row) in a video wall.

• IR Mode: Selects whether the remote control controls all displays in a video wall (All), none of

the video displays in the video wall (Off), or one display at a time (Target).

• Recipient ID: Selects which display in a video wall is controlled by the remote control. This

feature is only active when IR Mode is set to Target.

Factory Reset

To reset ALL display settings (including image settings) back to their factory defaults, choose
Factory Reset from the Advanced Settings menu.

To change a display’s position in a video wall, first select that display’s Monitor ID using the

pull-down menu.

This action is not reversable. Proceed with caution!

ON

hides joints between displays:

(suitable for moving image display)

OFF

shows joints between displays:

(suitable for still image display)

«
...
42
43
44
45
46
...
»

Summary of Contents for FHD552-X







































































Reviews:

No comments