background image

Section 3: Operation 

 

Christie DS+60/DW30/Matrix 3000 User’s Manual     3-31  

Advanced Image Settings 

— SUBMENU 

Use the Advanced Image Settings 
submenu to make the adjustments 
necessary for lesser-used but more 
specialized applications on your 
projector. 

GAMMA TABLE:

 

This control applies a 

default video or graphics gamma 
table or “curve” to your images, 
controlling the intensity of midlevel 
colors and producing maximum 
contrast, brightness and color 
performance. As shown at right, the 
graphics curve is a simple power curve 
while the video curve has a linear 
segment near black to compensate for 
increased blacklevels typical of video 
signals. Although the projector 
automatically applies either the graphics 
or video curve according to what type 
of incoming signal is detected, in some cases you may wish to override this default 
and use graphics gamma for a video source or video gamma for a graphics source. 
Alternatively, if neither default is ideal, you may prefer to apply a user-defined 
custom gamma curve that has been created externally, named, and downloaded to the 
projector (requires separate PC-based Arbitrary Gamma and KoRE Librarian software 
applications). If any of these special user curves have been installed, their names will 
appear in the Gamma Table pull-down list. 

Keep in mind that any Gamma Table choice sets the related Gamma value (shown in 
the Image Settings menu) to a 2.5 default, where it can be fine-tuned as desired. 
Different values (1-3) here indicate that the original gamma table has been adjusted 
with either the Gamma slidebar or direct key. 

NOTES: 1) If no user curves have been defined and downloaded to projector memory, 
only the “2.5, Graphics/Video Normal” default gamma curve is available here – 
adjust as desired using gamma in the main Image Settings menu. 2) Some graphic 
material will look best with the video setting while some video material is best with 
the graphic setting. 

SELECT COLOR ADJUSTMENT:

 

In “Select Color Adjustment”, 

choose an overall color palette for all images. The “Max 
Drives” factory default simply drives all 3 colors at their 
maximum level so that they are fully on and cannot be 
changed. The two other pre-defined color adjustment 
choices—SD Video and HD Video—apply a color gamut 
optimized for video sources (standard or high-definition). 
Alternatively, you can specify a color temperature. This 
enables the adjacent Color Temperature slidebar and applies 
its current setting (default = 6500K). If none of the pre-defined “Select Color 
Adjustment” options or color temperatures suit your application, select one of four 
color gamuts previously defined by a user (User 1, 2, 3, 4). A “User” option applies a 

 

 

 

 

 

 

Summary of Contents for DS+60











































































































































Reviews: