Christie DHD630-GS Service Manual Download Page 47

Page: 47 / 79

GS Series 630-635 Service Manual

020-001224-02 Rev. 1 (08-2018)

Parts and module
replacement

When ordering replacement parts, provide the following information found on the product license
label:

• Projector model

• Projector serial number

• Manufacture date

Maintenance prerequisites

Before servicing the projector, perform the following tasks.

• Always power down and disengage all power sources to the projector prior to servicing.

• Follow all service safety guidelines.

• For detailed breakdown of serviceable modules, see Index of parts and modules.

Tools required for service

The tools required for service are listed below.

• Phillips #1 screwdriver

• Phillips Jewelers screwdriver
• Flathead 3/16" X 4" screwdriver
• Flathead 1/16" X 4" screwdriver

• M4 allen key

• M3 socket driver

• M6 socket driver

• Side cutters

• Electrostatic protective strap and pad

• Cloth wipes

Summary of Contents for DHD630-GS
















































































Search results

Summary of Contents for DHD630-GS

Reviews:

Related manuals for DHD630-GS

Brands by name

Popular brands

Christie DHD630-GS, Service Manual

Search results

Summary of Contents for DHD630-GS

Reviews:

Related manuals for DHD630-GS

Brands by name

Popular brands