Chongqing Xiegu Technology X5105 Page 7 Instruction Manual Download

Page: 7 / 56

Left interface

24 Antenna interface

BNC interface, impedance 50Ω.

25 Intermediate frequency signal outlet

The output receives the first intermediate frequency

signal.

26 Left supinterface

Break out the bracket when use it. After using, retract the side

guard.

27 Earphone interface

This interface is a 3.5mm stereo socket (3 wires) for connecting

earphone devices.

*this interface function of different versions of the X5105 is

different, be careful to distinguish.

28 DC power interface

External DC power input interface, using the distribution of power

wires to the external DC power supply to this interface. External

DC power must be able to provide 13.8 V @ 3A power output. The

interface is also used to charge the battery inside the machine.

EXT DC

Summary of Contents for X5105

























































Search results

Summary of Contents for X5105

Reviews:

Related manuals for X5105

Brands by name

Popular brands

Chongqing Xiegu Technology X5105, Instruction Manual

Search results

Summary of Contents for X5105

Reviews:

Related manuals for X5105

Brands by name

Popular brands