Chongqing Xiegu Technology X5105 Instruction Manual Download

Page: 48 / 56

System parameter configuration

Restoration of factory setting

When the system parameter setting error causes the host to be unable to work, the reset operation can be used to reset the transceiver. At that time, all

system parameters on the transceiver will be restored to the factory default data.

Operation method:

Enter the system menu, select item 22

【

Reset ALL

】

menu, rotate the main knob to set it to "

YES

" and press [

YES

] button below the screen.



After reset, all system parameters will revert to the factory default status.



According to the serial number of your device, combined with the [configuration parameter list ], the system menu part of the project will be

reconfigured and saved.



When all settings are complete, press [ YES ] button to save.

Summary of Contents for X5105

























































Search results

Summary of Contents for X5105

Reviews:

Related manuals for X5105

Brands by name

Popular brands

Chongqing Xiegu Technology X5105, Instruction Manual

Search results

Summary of Contents for X5105

Reviews:

Related manuals for X5105

Brands by name

Popular brands