manualshive.com logo in svg

Chip Hyde VISION 3D, Instructions Manual, Page: 22 / 38

Share
Download
Chip Hyde VISION 3D Instructions Manual Download Page 22

 
Now glue the fin post in place with 20 minute epoxy. Clamp the fin post in 
place during this step. Apply clamps here to ensure good fin post adhesive 
bond Glue fin into position ensuring that the fin is upright & also aligned 
straight down the center of the fuselage. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

Apply clamps 
here to ensure  
good fin post 
adhesive bond

Glue fin into 
position 

 
 

10.2  Fitting and Hinging the Rudder 

 
To complete the fin and rudder installation fit/hinge the rudder in place. This 
should be done following the same steps used for the ailerons, fitting the 
rudder in place and then applying CA to the hinges. 
 

10.3  Rudder Servo and Control Linkage Installation 

 
Remove the covering at the rear of the fuselage over the opening for the 
rudder servo mounting point. Take one of the lite-ply servo mounting plates 
and glue it over the rear mounting point for the rudder servo using medium CA 
– this will require removing a small rectangle of covering material. 
 
 
 
 
 

Lite-ply 
mounting 
plate 

 
 
 
 
 
 
 
 
 
 

Summary of Contents for VISION 3D







































Reviews:

No comments