manualshive.com logo in svg

Chip Hyde VISION 3D, Instructions Manual, Page: 20 / 38

Share
Download
Chip Hyde VISION 3D Instructions Manual Download Page 20

9. 

Undercarriage and Tail Wheel Unit Installation 

 

9.1 Undercarriage 

Installation 

 
The vision 3D has been designed with a three-piece undercarriage assembly 
that allows the legs to be removed, for easier transportation and storage of 
the fuselage. This assembly is pictured below: 
 
 
 
 
 
 
 
 
 
 
 
 
 
The fuselage is supplied with captive nuts fitted in place for the 4mm 
undercarriage mounting bolts. Using the 6 mounting bolts fit the undercarriage 
in place. Use red Loctite on the two center bolts for the joining plate; as in the 
event the undercarriage legs are removed these bolts will be left in place.    
 
For now leave the axels, wheels and pants unfitted. 
 

9.2 

Tail Wheel Unit Installation 

 
While the fuselage is still upside down from fitting the undercarriage, fit the tail 
wheel unit using the supplied mounting screws as shown in the picture below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Add some thin CA to the fixing holes after drilling them and before screwing 
the tail wheel unit and black plastic (rudder) spring retainer in place. 

Summary of Contents for VISION 3D







































Reviews:

No comments