INST.No.INE-454-P2 Software
Ver.1.2
-C2 -
1.
Operation·········································································· 1
1.1
Digital display···································································· 1
2.
Operation mode and engineering mode···················· 1
2.1
Parameter programming /selection (Operating mode)···· 1
2.2
Parameter programming /selection (Engineering mode) 2
3.
Operating mode······························································· 3
3.
Details of the operator mode··············································· 3
3.1
Emissivity (ratio) programming ······································· 3
3.1.1
Emissivity (ratio) programming 1 ································· 3
3.1.2
Emissivity (ratio) programming 2 ································· 4
3.2
Automatic emissivity calculation ····································· 4
3.2.1
Automatic emissivity calculation
(Internal):Input of reference temperature·················· 4
3.2.2
Automatic emissivity calculation
(External):Model IR-CAQ
5
only : Selection
of external programing ················································ 5
3.3
Signal modulation mode selection ··································· 5
3.4
Modulation degree programming····································· 6
3.4.1
Modulation time constant programming
(Effective when the “dELy” is selected in the signal
modulation mode.)······················································ 6
3.4.2
Damping degree selection
(Effective when the “PEAk” is selected in the signal
modulation mode.)······················································ 6
3.5
Alarm programming
(Model IR-CAQ
J
only constant output
possible : As for other models “AL”,”AH” of the
status marker are lighted)············································ 7
3.5.1
Alarm type selection
(High alarm, low alarm or alarm disable) ················· 7
3.5.2
Alarm set-point (1 point only in high alarm in
[3.5.1 Alarm type selection]) ··································· 7
4.
Engineering mode··························································· 8
4.1
Analog output scaling programming································ 8
4.1.1
Analog output minimum value programming…”OutL”· 8
4.1.2
Analog output maximum value programming…”OutH”·· 8
4.2
Analog dummy output programming······························ 9
4.3
Hold functions (Hold disable, Sample hold Peak hold) selection ····10
4.3.1
Hold functions type selection ········································ 10
4.3.2
Peak hold reset type selection (Selection of he outside
reset… Model IR-CAQ
J
only)··············· 11
4.3.3
Peak hold reset time programming ······························· 12
4.4
Measurement unit selection·············································· 12
4.5
Modulation time constant unit selection ·························· 13
4.6
Contact output item selection
(Model IR-CAQ
K
only) ····································· 13
4.7
Automatic emissivity calculation type selection
(External setting: Model IR-CAQ
5
only)··········· 14
4.8
Measuring wavelength selection ······································ 15
4.9
Zero/span adjustments ······················································ 16
4.9.0
Procedure for Zero/span adjustments···························· 16
4.9.1
Zero/span adjustments (1)·············································· 16
4.9.1-1) Zero/span adjustments execution selection ················· 16
4.9.1-2) “Zero” side adjustments
···
Adjustment by furnace
temperature at zero side························· 16
4.9.1-3) “Span” side adjustment
···
Adjustment by furnace
temperature at span side························· 16
4.9.2
Zero/span adjustments (2)·············································· 17
4.9.2-1) Zero/span adjustments execution: For “2coL”············ 17
4.9.2-2) Zero/span adjustments execution: For “1coL”············ 17
4.9.3
Correction after the Zero/span adjustments.
(measured value became abnormal) ··········· 17
4.9.3-1) Zero/span adjustments execution selection ················· 17
4.9.3-2) Zero side data display/setting by IR-CA series············ 18
4.9.3-3) Zero side data display/setting by furnace
temperature by a reference radiation thermometer······· 18
4.9.3-4) Span side data display/setting by IR-CA series
radiation thermometer·································· 19
4.9.3-5) Zero side data display/setting by furnace
temperature by a reference radiation thermometer······· 19
4.9.4
Selection of correction after the zero/span
adjustments programming item······················· 20
4.10
Temperature display/Analog output
correction programming································ 21
4.10.1
Programming of number of temperature display
and analog output correction data
(number of knee-point)·············· 21
4.10.2
Programming of temperature display and analog
output correction data No.··························· 21
4.10.3
Entering of data before temperature display and
analog output correction ···························· 22
4.10.4
Entering of data after temperature display and
analog output correction ···························· 22
4.10.5
Selection of temperature display and
analog output correction for programming item········· 23
4.11
Analog input programming
(Model IR-CAQ
5
only) ································24
4.11.1
Selection of analog input items···································· 24
4.11.2
Emissivity scaling for
remote emissivity programming ············· 25
4.11.3
Temperature scaling for
automatic emissivity calcuiation························ 26
4.12
Communications programming
(Model
IR-CAQ
S
only) ··································27
4.12.1
Address programming ················································· 27
4.12.2
Communication speed selection·································· 27
4.12.3
Communication protocol mode selection ··················· 28
4.13
Key lock··········································································· 28
5.
Self-diagnostic function and Overflow/underflow ·· 29
5.1
Self-diagnostic function ···················································· 29
5.2
Overflow/underflow·························································· 29
5.3
Under flow display for two-color type radiation
thermometer only : “CLP” ······································ 29
6.
List of starting up modes ··············································· 30
6.1
Starting up modes······························································ 30
6.2
Screens················································································30
7.
Parameter programming/selection
····························· 30
7.1
Parameter programming/selection (operating mode)·······30
7.2
Parameter programming/selection (engineering mode)·· 31
Software Version Ver.1.2
CONTENTS