background image

CM6SV65 and 83

Installation Instructions

2

CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However,
CSAV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV
assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

 IMPORTANT WARNINGS AND CAUTIONS!

The Alert messages

DANGER

,

WARNING

,

CAUTION

,

IMPORTANT

, and

NOTE

 are used throughout these instructions and on the

product to alert the reader and/or operator of the existence of dangerous situations, conditions and/or important operational and
maintenance information.

"SAVE THESE INSTRUCTIONS"

WARNING:

 WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the

corresponding instructions.

WARNING:

FAILURE TO READ AND FOLLOW THE FOLLOWING INSTRUCTIONS CAN  RESULT IN SERIOUS PERSONAL

INJURY, DAMAGE TO EQUIPMENT OR VOIDING OF FACTORY WARRANTY. It is the installer’s responsibility to make sure all
components are properly assembled and installed using the instructions provided.

Read all instructions before using this

furnishing.

DANGER:

TO REDUCE THE RISK OF ELECTRIC SHOCK:

ALWAYS unplug this furnishing from the electrical outlet before cleaning.

WARNING:

TO REDUCE THE RISK OF BURNS, FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS:

Unplug from outlet before putting on or taking off parts.

Close supervision is necessary when this furnishing is being used by, or near, children, invalids, or disabled
persons.

Use this furnishing only for its intended use as directed in these instructions. DO NOT use attachments not
recommended by the manufacturer.

NEVER operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been
dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and
repair.

Keep the cord away from heated surfaces.

NEVER operate the furnishing with the air openings blocked. Keep the air openings free of lint, and the like.

NEVER drop or insert anything into any opening.

DO NOT use outdoors.

DO NOT operate where aerosol (spray) products are being used, or where oxygen is being administered.

To disconnect, turn all controls to the off position, then remove plug from outlet.

WARNING:

RISK OF ELECTRICAL SHOCK! Connect this device to a properly grounded outlet only.

CAUTION:

ONE END OF POWER CORD MUST REMAIN ACCESSIBLE AT ALL TIMES! DO NOT block or impede access to

plug at any time!

CAUTION:

Changes or modifications to this unit not expressly approved by the manufacturer can void the units FCC

compliance rating and make the unit illegal to operate.

Summary of Contents for CM6SV65











Reviews: