DIGITAL LOCKSET COMPONENT PARTS LIST
INSTALLATION OF MORTICE LOCK OR DEADLATCH LOCK
C D L 7 1 0 0 D I G I T A L L O C K S E T M O R T I C E A N D D E A D L A T C H K I T
INSTALLATION
INSTRUCTIONS
Distributed in Australia by
LOCK AND KEY a division on the
DAVCOR GROUP PTY LTD ABN 95 003 562 598
This product has been manufactured in Taiwan
to Lock and Key Company specifications
This product is guaranteed to be free from defects in materials and
workmanship for a period of one (1) year from the date of original
purchase. This warranty is for replacement of product only and Lock
and Key Company does not accept responsibility for any direct or
consequential damage caused by this product or its use. This warranty
does not cover damage
that results from faulty installation or usage,
alteration or modification of the product or tarnishing of the finish
including colour change due to weather, salt or chemical. Should this
product not perform satisfactorily in its intended application, return it
to place of purchase for replacement.
LOCK & KEY
Phone:
1300 652 692
Web:
www.locknkey.com.au
Web:
www. daveweb.com.au
NOTE
Please dispose of plastic
bags and other packaging
in a thoughtful manner
WARNING
Please keep contents
away from small children.
Suffocation Hazard.
SPECIAL NOTES:
Before commencing installation please check that all components are working correctly.
- Take the front body lock assembly, enter in the factory code
C13579
and turn the handle. Repeat, but turn the handle
in the other direction. The handle should return freely under spring pressure.
- It is important that the code is changed and tested before fitting. See code change instructions for details.
CHANGING THE CODE NUMBER
1) The digital lock is supplied with the default code of C13579
2) Determine the code you want to use and slide the
selectors into position.
3) To do this, depress the code select button and slide it left
or right depending on whether it’s part of the code or not.
4) When the button is showing the red indicator this means
that the corresponding button is part of the code.
5) The CLEAR “C” button MUST always be used before any
code is inputted into the lock.
6) To achieve higher levels of security, it is recommended
that the code should contain 4-5 digits.
7) After the clear button is depressed, the digits can be
entered in any order. EG: In the image shown it would be
possible to enter CW1982 as well as C1289W because any
combination of the digits will unlock the lock.
Code select
buttons
Red indicators
Slide left or right
TOOLS REQUIRED
- 32mm Hole Saw
- 16mm Spade Bit
- 8.5mm Drill Bit
- Phillips Head Screwdriver
2
3
4
1
2
3
4
1
8
13
6
7
5
11
10
9
12
8
13
6
7
5
11
10
9
12
Description
BOM ID Qty
Front Lock Body
1
1
Gasket
1
2
M5 14mm Screw
2
Mortice Adaptor Plate
1
Mortice Tailbar Spring
1
Mortice Tailbar
6
1
Trim Washer
7
1
Drive adaptor
8
1
25mm M5-M4 Hex Lug
1
25mm M4-M5 Hex Lug
Rimlock Tailbar
11
10
9
4
3
5
1
M4 x 65mm CSK Screw
50mm M5x0.8 Phillips Head 13
12
2
2
2
Parts Pack
Exploded View
1)
Check the handing of
the door.
As shown in
fig
1
, the door’s handing is
dependant upon which
side the lock assembly is
mounted. When viewed
from the outside if the
lock is on the right it’s
right-handed and if it’s on
the left it’s left-handed.
2)
Installing CDL7100
assembly to a Mortice Lock.
Installation holes must be drilled in exactly the correct positions and precisely at right angles
to the door surface. Lock components must
be vertically and horizontally accurate in
relation to each other and to the door.
• With a new installation, you must first use
the factory template and instructions for
fitting the mortice lock before fitting the
digital lock. Insert the mortice lock.
• You now need to attach the supplied
drilling template to the door (shown in
fig 2
).
• The mortice lock holes are shown in grey
• Fold template around the edge of the
door. Line up the mortice handle axis on the
template to the centre of the handle axis
on the lock. Attach the template to the
door with low adhesive tape.
• Now position the furniture supplied with
the mortice lock up to the template. Line up
the furniture handle drive axis with the
centre line of latch and mark off one of the
upper holes that needs to be drilled for the
furniture mounting screws. The lower hole is
positioned so that it fits the majority of
furniture sets available. Select one of the
two 8.5mm holes within the 16mm diameter
recess for the bottom of the furniture.
• Now remove the mortice lock.
IMPORTANT: you will not need to drill completely through all of the holes.
• Mark the lower hole and use the 16mm spade bit to drill the 10mm deep
recess for the lower connecting stud.
• Mark and drill the chosen 8.5mm fixing holes for the furniture. Drill the
10mm deep recess for the unused top connecting stud.
• At this point all the holes for the digital lock will be drilled out and you can
remove the fitting template.
Instructions continued overleaf.
fig 2
Fold along the edge of the door ( Match to BACKSET of LATCH )
Fold along the edge of the door ( Match to BACKSET of LATCH )
60mm
Centre line of latch
Centre line of latch
60mm
Outline of
rubber seal
Outline of
Lockcase
C D
L 7 1
0 0
D I G
I T A
L L
O C
K S E
T
FIT
TIN
G
TE
MP
LAT
E
Distributed in Aus
tralia by
LOCK AND KEY a
division on the
DAVCOR GROU
P PTY
LTD ABN 95
003 562 598
This pro
duct has been
manufactured
in Taiwan
to Lock and Key
Company specifica
tions
This pro
duct is gua
ranteed to be free fro
m defects in material
s and
workmanship for a
period of one (1) year fro
m the date of origina
l
purchase. This warra
nty is for replacemen
t of pro
duct only
and Lock
and Key Company doe
s not accept resp
onsibility for any direct
or
consequential d
amage caused by this
pro
duct or its us
e. This warranty
does not cover
damage
that results
from faulty insta
llation or usage
,
alteration or m
odification of
the product o
r tarnishing of
the finish
including colou
r change du
e to weather
, salt or chem
ical. Should t
his
product not pe
rform satisfac
torily in its in
tended applica
tion, return it
to place of
purchase for rep
lacement.
LOCK & KEY
Phone:
1300 652 692
Web:
www.lock
nkey.com.au
Web:
www. daveweb.com.au
Key
- Mortice lock holes
- Deadlatch/Nightlatch holes
8.5mm
8.5mm holes
16mm
32mm
Recess hole 10mm only
Mortice lock handle axis
Only drill through
the required hole
121.5mm
104.5mm
129.5mm
40.5mm
Only drill
through the
required hole
and recess
the other
Fold along the edge of the door ( Match to BACKSET of LATCH )
Fold along the edge of the door ( Match to BACKSET of LATCH )
60mm
Centre line of latch
Centre line of latch
60mm
Outline of
rubber seal
Outline of
Lockcase
C D L 7 1
0 0 D IG
I T A L L
O C K SE
T
FITTIN
G
TEMP
LATE
Distributed in Austral
ia by
LOCK AND KEY a d
ivision on the
DAVCOR GROUP P
TY LTD ABN 95 003 562 5
98
This pro
duct
has been manufactu
red in Taiwan
to Lock and Key
Company specifications
This pro
duct
is guaranteed to be free
from defects in ma
terials and
workmanship fo
r a period of one (1) y
ear fro
m the date of o
riginal
purchase. This w
arranty is for replace
ment of pro
duct only an
d Lock
and Key Company
does not accept
responsibility for any dire
ct or
consequential d
amage caused by t
his pro
duct or its u
se. This warranty
does not cove
r damage
that results from faulty installa
tion or usage,
alteration or modification of the product or tarnishing of the finish
including colour change due to weather, salt or chemical. Should this
product not perform satisfactorily in its intended application, return it
to place of purchase for replacement.
LOCK & KEY
Phone:
1300 652 692
Web:
www.locknkey.com.au
Web:
www
. daveweb.com.au
Key
- Mortice lock holes
- Deadlatch/Nightlatch holes
8.5mm
8.5mm holes
16mm
32mm
Recess hole 10mm only
Mortice lock handle axis
Only drill through
the required hole
121.5mm
104.5mm
129.5mm
40.5mm
Only drill
through the
required hole
and recess
the other
latchbolt.
• The Deadlatch/Nightlatch holes are shown in diagonal
black stripes. Mark and drill the top 8.5mm front lock
body fixing hole.
• Use the hole saw to drill the 32mm rim lock hole if not
already done.
4)
Installing the
components to suit the
application.
• As shown in
fig 5
,
screw the two M4-M5
Hex Lugs and M5-M4
Hex Lug into the back
plate of the lock body.
• Measure the
thickness of the door
and cut the rimlock
tailbar to the
corresponding length.
• If the CDL7100
digital lock is being
installed onto an
Australian type
Deadlatch Lock (such
as the Whitco or
Lockwood 001 type),
cut the rimlock tailbar
(part #11) to the
correct length using
the gauge on the tail
bar. NOTE: cut the
opposite end to the
pin stop in the tailbar.
• When installing the
CDL7100 digital lock onto an Australian type Nightlatch Lock, due to the variation in Nightlatch design, do not cut the tail
bar straight away.
• Attach the Nightlatch if not already attached to the door.
• Insert the tail bar into the nightlatch in the orientation shown in
fig 5
.
• Place the front lock assembly and gasket onto the door as it would be mounted, making sure that the tailbar is going into the drive adaptor.
• If the CDL7100 digital lock cannot sit on the face of the door, remove sections from the end of the tail bar until it can.
6)
Fixing the CDL7100 digital lock to the door
• Insert the drive adaptor into the lock body so it is able to accept the rimlock tailbar.
• Add the gasket to the CDL7100 digital lock and position it onto the door.
• As shown in
fig 5
, insert the M4 CSK screw into the Trim Washer through the top hole and into the CDL7100 lock. Do not fully tighten the screw.
• Please note, the screw will have to be cut to length depending on the depth of the door.
• Insert the rimlock tail bar into the drive adaptor and into the CDL7100 lock through the hole in the door as shown in
fig 5
.
• Secure the CDL7100 digital lock at the bottom using the two M5 Phillips head screws. They will need to be cut to length depending on the door thickness.
• Depending on the type of latch being used, use the Deadlatch mounting plate to connect to the Hex Lugs on the CDL7100 Lock. Or if necessary, in the
case of using with a nightlatch, use the rim lock plate that is supplied with the nightlatch. Do not fully tighten screws.
• Before final tightening, make sure that the lock is vertical and test that the lock is operating correctly. Do not close the door until you are sure that the
entry code works. Now tighten all of the screws and test the locks operation again. Do not over tighten the fixing screws as this may cause distortion and
lead to poor operation.
RIGHT HAND OPEN OUT
LEFT HAND OPEN OUT
OUTSIDE
LEFT HAND OPEN IN
RIGHT HAND OPEN IN
OUTSIDE
fig 1
