Installation Guide
Lock Parts
Mounting
Screws
Screw type
M3×10
✓
0 – 5 mm
✓
M3×14
5 – 8 mm
M3×10
8 – 12 mm
M3×14
12 – 16 mm
M3×18
16 – 20 mm
Mounting plate
Accommodates door
thickness up to 20 mm
Mortise Hole Dimensions
Spacer Requirements
Spacer required* for door
thickness less than 8 mm
Factory default combination 0-0-0-0
Removal key
Manager key
Door thickness
*Spacer required
R3
77 mm
31.5 mm
min. 6.35 mm
Cam in Locked Position
must overlap Strike
Plate by at least ¼"
(6.35 mm)
Mounting
Screws
Screw type
M3×10
✓
0 – 5 mm
✓
M3×14
5 – 8 mm
M3×10
8 – 12 mm
M3×14
12 – 16 mm
M3×18
16 – 20 mm
Mounting plate
Accommodates door
thickness up to 20 mm
Mortise Hole Dimensions
Spacer Requirements
Spacer required* for door
thickness less than 8 mm
Factory default combination 0-0-0-0
Removal key
Manager key
Door thickness
*Spacer required
R3
77 mm
31.5 mm
min. 6.35 mm
Cam in Locked Position
must overlap Strike
Plate by at least ¼"
(6.35 mm)
Mounting
Screws
Screw type
M3×10
✓
0 – 5 mm
✓
M3×14
5 – 8 mm
M3×10
8 – 12 mm
M3×14
12 – 16 mm
M3×18
16 – 20 mm
Mounting plate
Accommodates door
thickness up to 20 mm
Mortise Hole Dimensions
Spacer Requirements
Spacer required* for door
thickness less than 8 mm
Factory default combination 0-0-0-0
Removal key
Manager key
Door thickness
*Spacer required
R3
77 mm
31.5 mm
min. 6.35 mm
Cam in Locked Position
must overlap Strike
Plate by at least ¼"
(6.35 mm)
Setup
Note:
Removing the Programming Key in the circle mark position will remove the core. See Replace Key Set and Core instructions to reinsert the core.
Mounting
Screws
Screw type
M3×10
✓
0 – 5 mm
✓
M3×14
5 – 8 mm
M3×10
8 – 12 mm
M3×14
12 – 16 mm
M3×18
16 – 20 mm
Mounting plate
Accommodates door
thickness up to 20 mm
Mortise Hole Dimensions
Spacer Requirements
Spacer required* for door
thickness less than 8 mm
Factory default combination 0-0-0-0
Removal key
Manager key
Door thickness
*Spacer required
R3
77 mm
31.5 mm
min. 6.35 mm
Cam in Locked Position
must overlap Strike
Plate by at least ¼"
(6.35 mm)
Assign a User Combination
Once a new user combination is assigned, the previously assigned user combination will no longer operate the lock. If the current user code
is unknown, follow the Reset Combination instructions to find the current assigned code then continue to Assign a new User Combination.
1.
Set the dial to show the current assigned combination.
2.
Insert the Programming Key and turn the knob to the
circle mark position.
3.
Set any 4-digit combination.
4.
Turn the knob to the locked position and remove the
Programming Key.
5.
Scramble the code.
Dial Combo
Assigned Use
Product Guide
Rear Unit
Front Unit
Locked Position
Reset Pin Holes
Key Slot
Unlocked Position
Programming
Position
Comibination Dial
Cam
