background image

Installation Instructions

CM6SV65 and 83

3

TOOLS REQUIRED FOR INSTALLATION

PARTS

System Features and Installation Requirements

Features

Remote Control Activated Lutron Light Dimmer Module

With this dimmer cabinet lighting can be switched on or off and dimmed using the left buttons on the hand held remote control
transmitter.

Obstruction Sensor

The mechanism is equipped with a obstruction sensor. In the event that something would interfere the motion of the doors; the
doors stop, reverse, run a few seconds, and then stop again.

Auxiliary Controls

There is an activator button located on the front of the motor box which will activate the doors.

Status Light

The Status Light on the front of the Motor Box indicates the operating condition of the mechanism. In normal operating conditions,
the status light will be solid green with the doors at rest and will blink a series of green
twice, pause, green twice, pause ..., when the doors are in motion.

Installation Requirements

115VAC power at installation site

Doors must be made of a non warping material.

Maximum door width = 72"

Maximum door weight = 50 Ibs

(B) x1

(A) x1

(D) x1

(E) x1

(G) x2

(C) x1

(with motor)

(F) x2

Summary of Contents for CM6SV65











Reviews: