![background image](http://html1.mh-extra.com/html/chief/avm1/avm1_installation-instructions-manual_2600255004.webp)
AVM1
Installation Instructions
4
DIMENSIONS - AVMV
3.43
2.92
3.27
2.56
2.75
4.17
Specifications and Requirements
Mains Input Power
100-240VAC, 50-60Hz / Energy Star Rated
Input Power
(to AVM1)
24VDC/2.5A regulated switching wall supply, UL1310 Class 2, Energy Star, FCC, CUL,
CE listed (provided).
Output Power
(from AVM1)
25W Peak 4 per channel 12W RMS continuous 4 per channel.
Audio Performance (AVMA)
Frequency Response
: 20Hz - 20kHz ( ± 1.5dB )
THD + N
: < 1.0% at 1kHz rated output, < 0.1% at 1kHz at 10W 4
Signal to Noise Ratio
: 90dB A-weighted (band pass: 20Hz-20kHz)
Channel Separation
: 60dB
Dynamic Range
: 100dB
Input Sensitivity & Impedance
: Program: 0.775V, 10k electronically balanced, with RF
filter (ferrite).
Outputs
(R + L): 4 (optimum) or 8
25V /70V with optional transformer model AVx70.
Output Regulation Controls
:
• Less than 2dB, no load to full load at 1kHz.
• Master Override (MO) audio level 0-1V POT.
• Master Override (MO) voltage sensitivity 1V-70V POT.
• Master Override (MO) delay (time sec) POT.
• Volume gain POTS on Preamp and Amp.
• Treble and bass POT.
• Power On/Off soft push button.
• Manual ‘Duck’ (1 to -50dB) for Mic input.
Controls-IR Remote
:
• Volume (+/-, R+L), Mute, Balance (R+L), On/Off
• Redundant manual soft push buttons.
• AVM1 provided with (2) AA batteries.
Video Performance (AVMV)
• Supports VGA, SVGA, XGA , WXGA computer video to VESA standard.
• Supports NTSC, PAL and SECAM video standards.
• Output transmission via CAT5e meeting ANSI /EIA / TIA 568B standard.
• Operational bandwidth up to 350MHz.
• Horizontal frequency 15-126 kHz.
• Vertical frequency 43-200 Hz.
• Sync signal compatible with TTL level 5V / 3.3V.
• Power at 5VDC nominal from 24VDC/2.5A wall supply (AVMA).
• Video differential gain / phase at +/- 2%.
• Attenuation loss rated at 6 dB at 1,000 feet at 1MHz typical UTP CAT5e.
• Maximum capacitance at 20pf/foot UTP.
Video Performance (AVxVR)
• Supports VGA, COMPOSITE AND S-VIDEO
• Override priority to ’video’ inputs allows simultaneous use with VGA source.
• Interface and control of AV screens via Phoenix dockable connectors
• Push button calibration with visual LED relative to distance (1’ to 300’)
• AM/FM ’RF’ and audible noise suppression
• Signal to noise at 85dB and sensitivity at -16dBu
• Output transmission via CAT5e UTP cabling up to 300’/90M wired per EIA/TIA 568 standard.
• Operational bandwidth up to 350MHz.
• Video differential gain/phase at 2%.
• Attentuation loss at 1dB at 300’ at 1 MHz.
• Maximum capacitance at 20pf/foot UTP and 75 -100 impedance matching.
• Power at 5VDC nominal from 24VDC/2.5A wall supply (AVMA).
Power Efficiency
<80% at 25W 4 , <85% @ 8 , <90% at 10W 4 , <95% @ 8
Power Consumption
32W / 9.5 btu @ 120VAC, 130ma nominal in ‘Sleep’ mode.
Operating Temperature
-10° to 40°C, 14 to 104°F
Storage Temperature
-20° to 65°C, -4 to 149°F
Input selections
(3) Stereo/Mono inputs: 3-pin dockable, RCA and 3.5mm jack.
(1) 3-pin dockable Mic or Audio line level (Stereo/Mono).
(1) 2-pin dockable EAO-1 Emergency Audio Off override closure (no polarity).
(1) 2-pin dockable EAO-2 Emergency Audio Off override closure with tone (no polarity).
(1) 2-pin dockable MO override input (+/-).
(1) HD-15 VGA/RGB
(1) 4-pin Mini DIN S-video
(1) RCA Composite video
Output Connections
(2) 2-pin dockable Speaker (R+L).
(1) 3-pin dockable Audio line out (1V/600 Ohm).
(1) RJ45 video out and video input
(3) RJ45 Audio/Power input and output between AVMA and AVMV
(1) IR LED remote 3.5mm jack
(1) Headphone 3.5mm jack
(1) HD-15 VGA/RGB, (1) Mini DIN S-video, (1) RCA C-video all with 12”+ cables
(1) HD-15 VGA buffered Monitor
Internal Connections
(2) 2x6 socket connectors (AVMA and AVMV backplane).
(2) 3-pin header/jumper option (AVMA backplane).
Visual Indicators
• Front LED video source active (green).
• Power LED for all plug-in modules (green).
• Internal LED for MO active (amber).
• Internal LEDs for power to each channel (green).
• Video signal present LEDs: VGA, S and C video (green).
•
4-character, 7-segment LED display for system setup and control.
• IrDA pairing LEDs (Blue / Red)
• RF Wireless battery chargers with status LED indication of charging / full charge condition
Material and Finish
1 AWG CRS steel / .047” nom. with zinc undercoat and white powder coat paint or CAD
plate.
Dimensions
: AVMA and AVMV units internal to EO box:
Length: 3.23” / 82mm, Width: 3.37” / 85.5mm, Height: 2.54” / 64.4mm
Dimensions:
AVMA and AVMV carton:
Length: 5.5” / 139.7mm, Width: 7.5” / 190.5mm, Height: 4.6” / 116.8mm
Weight:
AVMA, AVMV: Product:1.75 lbs., Shipping: 2.25 lbs.