Chevrolet MONTE CARLO 2005 Owner'S Manual Download | Manualshive

Page: 308 / 396

background image

Tire Size

The following illustration shows an example of a typical
passenger vehicle tire size.

(A) Passenger (P-Metric) Tire: The United States
version of a metric tire sizing system. The letter P as
the first character in the tire size means a passenger
vehicle tire engineered to standards set by the U.S. Tire
and Rim Association.

(B) Tire Width: The three-digit number indicates the
tire section width in millimeters from sidewall to sidewall.

(C) Aspect Ratio: A two-digit number that indicates
the tire height-to-width measurements. For example, if
the tire size aspect ratio is 60, as shown in item C of the
illustration, it would mean that the tire’s sidewall is
60 percent as high as it is wide.

(D) Construction Code: A letter code is used to
indicate the type of ply construction in the tire. The
letter R means radial ply construction; the letter D
means diagonal or bias ply construction; and the letter B
means belted-bias ply construction.

(E) Rim Diameter: Diameter of the wheel in inches.

(F) Service Description: These characters represent
the load range and speed rating of the tire. The load
index represents the load carry capacity a tire is certified
to carry. The load index can range from 1 to 279. The
speed rating is the maximum speed a tire is certified
to carry a load. Speed ratings range from A to Z.

Tire Terminology and Definitions

Air Pressure: The amount of air inside the tire pressing
outward on each square inch of the tire. Air pressure
is expressed in pounds per square inch (psi) or
kiloPascal (kPa).

Accessory Weight: This means the combined weight
of optional accessories. Some examples of optional
accessories are, automatic transmission, power steering,
power brakes, power windows, power seats, and air
conditioning.

5-62

«
...
306
307
308
309
310
...
»

Summary of Contents for MONTE CARLO 2005













































































































































































































































































































































































































Reviews:

No comments

Related manuals for MONTE CARLO 2005

Brand: APEXi Pages: 18

Brand: Prorack Pages: 15

Brand: Chevrolet Pages: 2

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: Honda Pages: 4

SAFESTOP SS0005

Brand: Pro-gard Pages: 4

Brand: AddSecure Pages: 14

Brand: TATA Motors Pages: 92

Brand: Cadillac Pages: 20

Brand: Pyle Pages: 8

Brand: Volvo Pages: 10

CHALLENGER HELLCAT 2017

Brand: Dodge Pages: 484

Heavy Duty ProClip

Brand: Brodit Pages: 2

BLADE-AL-HK4-EN

Brand: iDataLink Pages: 35

Brand: Prime Design Pages: 16

Chevrolet CAMARO 1969

Brand: GMC Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands