manualshive.com logo in svg

Chevrolet MONTE CARLO 2005, Owner'S Manual

The Chevrolet MONTE CARLO 2005 Owner's Manual is available for free download on our website. This comprehensive manual provides detailed instructions and information about your vehicle, ensuring a smooth and enjoyable driving experience. Don't miss the opportunity to access this valuable resource on manualshive.com.

Share
Download
background image

When the LOW TIRE PRESSURE message comes on,
you should stop as soon as you can and check all
your tires for damage. (If a tire is flat, see If a Tire Goes
Flat on page 5-75.) Also check the tire pressure in all
four tires as soon as you can. See Inflation - Tire
Pressure on page 5-65.

The LOW TIRE PRESSURE message will also be
displayed (while the ignition is on) until you reset
(calibrate) the system.

Don’t reset the tire pressure monitor system without first
correcting the cause of the problem and checking
and adjusting the pressure in all four tires. If you reset
the system when the tire pressures are incorrect,
the system will not work properly and may not alert you
when a tire is low.

Any time you adjust a tire’s pressure, rotate your tires,
or have one or more tires repaired or replaced, you’ll
need to reset (calibrate) the tire pressure monitor
system. You’ll also need to reset the system whenever
you buy new tires and whenever the vehicle’s battery
has been disconnected.

The tire pressure monitor system can be reset two ways.
To reset (calibrate) the system using the ignition, do
the following:

1. Turn the ignition position to ON.

2. Pull the exterior lamp control from the ON position

to the OFF position three times.

To reset (calibrate) the system through the radio, do
the following:

1. Turn the ignition to ACC or ON and turn the

radio off.

2. Press and hold the TUNE DISPL button on the

radio for at least five seconds until SETTINGS
is displayed.

3. Press the SEEK PSCAN up or down arrow to scroll

through the main menu.

4. Scroll until TIRE MON appears on the display.

5. Press the 1 PREV or 2 NEXT button to enter the

submenu. RESET will be displayed.

6. Press the TUNE DISPL button to reset. A chime will

be heard to verify the new setting and DONE will
be displayed for one second.

7. Once the monitor has been reset, scroll until EXIT

appears on the display.

8. Press the TUNE DISPL button to exit programming.

A chime will be heard to verify exit.

The system completes the calibration process
during driving.

5-67

Summary of Contents for MONTE CARLO 2005













































































































































































































































































































































































































Reviews:

No comments

Related manuals for MONTE CARLO 2005

Mazda 2012 Mazda6 Owner'S Manual preview
2012 Mazda6
Brand: Mazda Pages: 527
Cadillac 2008 Escalade EXT Owner'S Manual preview
2008 Escalade EXT
Brand: Cadillac Pages: 496
ECS Electronics CR-066-BHU Manual preview
CR-066-BHU
Brand: ECS Electronics Pages: 16
Subaru 2007 Impreza Brochure & Specs preview
2007 Impreza
Brand: Subaru Pages: 21
AA Products RB0007 Instruction Manual preview
RB0007
Brand: AA Products Pages: 6
Flash Cover MN002 Installation Manual preview
MN002
Brand: Flash Cover Pages: 2
Xhorse VVDI User Manual preview
VVDI
Brand: Xhorse Pages: 48
Rostra RearSight 250-8308 Installation Instructions preview
RearSight 250-8308
Brand: Rostra Pages: 2
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Brand: Saturn Pages: 440
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Brand: Cadillac Pages: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Brand: TIE DOWN Pages: 2
FALCON RIDGE CF-UFORCE-DRW01 Instructions For Installation And Care preview
CF-UFORCE-DRW01
Brand: FALCON RIDGE Pages: 6
Volvo XC70 - ANNEXE 808 Quick Manual preview
XC70 - ANNEXE 808
Brand: Volvo Pages: 8
Renault CAPTUR 2019 Vehicle Instruction Card preview
CAPTUR 2019
Brand: Renault Pages: 11
Genesis GV60 2022 Quick Reference Manual preview
GV60 2022
Brand: Genesis Pages: 29
Volvo XC60 2009 Owner'S Manual preview
XC60 2009
Brand: Volvo Pages: 304
Curt Manufacturing LIPPERT 18109 Installation Manual preview
LIPPERT 18109
Brand: Curt Manufacturing Pages: 3
Brodit 841488 Quick Start Manual preview
841488
Brand: Brodit Pages: 2

Brands by name

Popular brands

Load more brands