Chevrolet MONTE CARLO 2005 Owner'S Manual Download

Page: 118 / 396

Turn Signal On Chime

If you leave either one of your turn signals on and drive
more than three-quarters of a mile (1.2 km), a chime
will sound to alert you.

Headlamp High/Low-Beam Changer

To change your headlamps from low beams to high
beams, or from high to low, pull the multifunction lever
all the way toward you. Then release it.

While the high beams
are on, this light will
appear on the instrument
panel cluster.

This light works only while the key is in ON. The fog
lamps (if equipped) are not illuminated when the
high beams are on.

Flash-to-Pass

With the turn signal lever in the low-beam position, pull
the lever toward you momentarily to switch to
high-beam, (to signal you are going to pass).

If the headlamps are on, they will return to low-beam
when the lever is released.

This feature operates even if the headlamps are off.

3-8

Summary of Contents for MONTE CARLO 2005













































































































































































































































































































































































































Search results

Summary of Contents for MONTE CARLO 2005

Reviews:

Related manuals for MONTE CARLO 2005

Brands by name

Popular brands

Chevrolet MONTE CARLO 2005, Owner'S Manual

Search results

Summary of Contents for MONTE CARLO 2005

Reviews:

Related manuals for MONTE CARLO 2005

Brands by name

Popular brands