manualshive.com logo in svg

Chevrolet MONTE CARLO 2005, Owner'S Manual

The Chevrolet MONTE CARLO 2005 Owner's Manual is available for free download on our website. This comprehensive manual provides detailed instructions and information about your vehicle, ensuring a smooth and enjoyable driving experience. Don't miss the opportunity to access this valuable resource on manualshive.com.

Share
Download
background image

Aspect Ratio: The relationship of a tire’s height to
its width.

Belt: A rubber coated layer of cords that is located
between the plies and the tread. Cords may be made
from steel or other reinforcing materials.

Bead: The tire bead contains steel wires wrapped by
steel cords that hold the tire onto the rim.

Bias Ply Tire: A pneumatic tire in which the plies are
laid at alternate angles less than 90 degrees to the
centerline of the tread.

Cold Inflation Pressure: The amount of air pressure in
a tire, measured in pounds per square inch (psi) or
kilopascals (kPa) before a tire has built up heat
from driving. See Inflation - Tire Pressure on page 5-65.

Curb Weight: This means the weight of a motor
vehicle with standard and optional equipment including
the maximum capacity of fuel, oil and coolant, but
without passengers and cargo.

DOT Markings: A code molded into the sidewall of a
tire signifying that the tire is in compliance with the
U.S. Department of Transportation (DOT) motor vehicle
safety standards. The DOT code includes the Tire
Identification Number (TIN), an alphanumeric designator
which can also identify the tire manufacturer, production
plant, brand and date of production.

GVWR: Gross Vehicle Weight Rating, see Loading
Your Vehicle on page 4-29.

GAWR FRT: Gross Axle Weight Rating for the front
axle, see Loading Your Vehicle on page 4-29.

GAWR RR: Gross Axle Weight Rating for the rear axle,
see Loading Your Vehicle on page 4-29.

Intended Outboard Sidewall: The side of an
asymmetrical tire, that must always face outward when
mounted on a vehicle.

KiloPascal (kPa): The metric unit for air pressure.

Light Truck (LT-Metric) Tire: A tire used on light duty
trucks and some multipurpose passenger vehicles.

Load Index: An assigned number ranging
from 1 to 279 that corresponds to the load
carrying capacity of a tire.

Maximum Inflation Pressure: The maximum air
pressure to which a cold tire may be inflated. The
maximum air pressure is molded onto the sidewall.

Maximum Load Rating: The load rating for a tire at the
maximum permissible inflation pressure for that tire.

Maximum Loaded Vehicle Weight: The sum of curb
weight; accessory weight; vehicle capacity weight;
and production options weight.

5-63

Summary of Contents for MONTE CARLO 2005













































































































































































































































































































































































































Reviews:

No comments

Related manuals for MONTE CARLO 2005

Barker 25895 Owner'S Instructions preview
25895
Brand: Barker Pages: 2
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Brand: Subaru Pages: 34
Yescom YES5062 User Manual preview
YES5062
Brand: Yescom Pages: 4
Z Automotive Tazer DT User Manual preview
Tazer DT
Brand: Z Automotive Pages: 16
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Brand: Dakota Digital Pages: 3
Ford 2005 P207 Explorer Sport Trac Owner'S Manual preview
2005 P207 Explorer Sport Trac
Brand: Ford Pages: 540
EUFAB 16458 Operating Instructions Manual preview
16458
Brand: EUFAB Pages: 16
Draw tite 24963 Installation Instructions preview
24963
Brand: Draw tite Pages: 4
EFILive CM2350B User Manual preview
CM2350B
Brand: EFILive Pages: 25
BrandMotion FLTW-7511 Installation Manual preview
FLTW-7511
Brand: BrandMotion Pages: 6
Broadfeet RSLX-385-68S Installation Instructions preview
RSLX-385-68S
Brand: Broadfeet Pages: 2
Mercedes-Benz CLS 2015 Operator'S Manual preview
CLS 2015
Brand: Mercedes-Benz Pages: 398
Lippert Stargazer Spirit XTR Skylight Installation Manual preview
Stargazer Spirit XTR Skylight
Brand: Lippert Pages: 8
HAKR TRIP 3 Instructions For Use Manual preview
TRIP 3
Brand: HAKR Pages: 9
Brodit ProClip 854676 Quick Start Manual preview
ProClip 854676
Brand: Brodit Pages: 2
Volvo XC70 - ANNEXE 808 Quick Manual preview
XC70 - ANNEXE 808
Brand: Volvo Pages: 8
Honda 2000 RL Owner'S Manual preview
2000 RL
Brand: Honda Pages: 330
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Brand: Blue Ox Pages: 9

Brands by name

Popular brands

Load more brands