manualshive.com logo in svg

Chevrolet MONTE CARLO 2005, Owner'S Manual

The Chevrolet MONTE CARLO 2005 Owner's Manual is available for free download on our website. This comprehensive manual provides detailed instructions and information about your vehicle, ensuring a smooth and enjoyable driving experience. Don't miss the opportunity to access this valuable resource on manualshive.com.

Share
Download
background image

OIL LIFE (Engine Oil Life
System Reset)

This feature allows you to reset the engine oil life
system after an oil change. See Engine Oil Life System
on page 5-22. Be careful not to reset the OIL LIFE
system at any time other than when the oil has
been changed.

In addition to the engine oil life system monitoring the
oil life, additional maintenance is recommended in
the Maintenance Schedule in this manual. See
Scheduled Maintenance on page 6-4 and Engine Oil on
page 5-18 for more information.

To clear the CHANGE ENGINE OIL light from the
instrument panel cluster and reset the oil life system,
do the following:

1. Scroll, using the SEEK PSCAN up or down arrows,

until OIL LIFE appears on the display.

2. Press the 1 PREV or 2 NEXT button to enter the

submenu. RESET will then be displayed.

3. Press the TUNE DISP knob to reset. A chime will

be heard to verify the new setting and DONE will
be displayed for one second.

The CHANGE ENGINE OIL light is now reset. You can
either exit the programming mode by following the
instructions later in this section or program the next
feature available on your vehicle.

TIRE MON (Tire Inflation Monitor Reset)

This feature allows you to reset the tire pressure
monitor after checking all tire pressures. See Tires on
page 5-59. To clear the LOW TIRE PRESSURE
light from the instrument panel cluster and reset the low
tire pressure monitor, do the following:

1. Scroll, using the SEEK PSCAN up or down arrows,

until TIRE MON appears on the display.

2. Press the 1 PREV or 2 NEXT button to enter the

submenu. RESET will be displayed.

3. Press the TUNE DISP button to reset. A chime will

be heard to verify the new setting and DONE will
be displayed for one second.

The low tire pressure monitor is now reset. You can
either exit the programming mode by following the
instructions later in this section or program the next
feature available on your vehicle.

2-40

Summary of Contents for MONTE CARLO 2005













































































































































































































































































































































































































Reviews:

No comments

Related manuals for MONTE CARLO 2005

Mazda 2007 MazdaSpeed6 Specification preview
2007 MazdaSpeed6
Brand: Mazda Pages: 12
femkes Hopper on Top User Manual preview
Hopper on Top
Brand: femkes Pages: 7
Safe Fleet inView 360 Fusion Calibration Manual preview
inView 360 Fusion
Brand: Safe Fleet Pages: 27
Seat ROADSIDE ASSISTANCE Handbook preview
ROADSIDE ASSISTANCE
Brand: Seat Pages: 44
Great Wall WEY VV5 Service Manual preview
WEY VV5
Brand: Great Wall Pages: 18
WIX WP9378 Installation Instruction preview
WP9378
Brand: WIX Pages: 2
Bestop 614.04 Installation Manual preview
614.04
Brand: Bestop Pages: 31
cam 40103 AL Mounting Instructions preview
40103 AL
Brand: cam Pages: 6
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Brand: Roadmaster Pages: 4
Mazda MX-3 1995 Workshop Manual preview
MX-3 1995
Brand: Mazda Pages: 1001
Poison Spyder TrailGate TJ Installation Instructions preview
TrailGate TJ
Brand: Poison Spyder Pages: 5
Kia 2015 Soul Features & Functions Manual preview
2015 Soul
Brand: Kia Pages: 46
Jeep 2018 GRAND CHEROKEE User Manual preview
2018 GRAND CHEROKEE
Brand: Jeep Pages: 372
Navman F-Series B2+ User Manual preview
F-Series B2+
Brand: Navman Pages: 10
Cruiser Consoles BUSHMAN 15L ROADIE fridge Base console Installation Instructions Manual preview
BUSHMAN 15L ROADIE fridge Base console
Brand: Cruiser Consoles Pages: 6
Jeep 2012 Patriot Series Owner'S Manual preview
2012 Patriot Series
Brand: Jeep Pages: 505
TRAMEC CV 1 Series Manual preview
CV 1 Series
Brand: TRAMEC Pages: 116
Baby Jogger CITY GO PD349056A Assembly Instructions Manual preview
CITY GO PD349056A
Brand: Baby Jogger Pages: 16

Brands by name

Popular brands

Load more brands