manualshive.com logo in svg

Chevrolet MONTE CARLO 2005, Owner'S Manual

The Chevrolet MONTE CARLO 2005 Owner's Manual is available for free download on our website. This comprehensive manual provides detailed instructions and information about your vehicle, ensuring a smooth and enjoyable driving experience. Don't miss the opportunity to access this valuable resource on manualshive.com.

Share
Download
background image

3. Simultaneously press and hold both the desired

button on HomeLink

®

and the hand-held transmitter

button. Do not release the buttons until Step 4
has been completed.

Some entry gates and garage door openers may
require you to substitute Step 3 with the procedure
noted in “Gate Operator and Canadian
Programming” later in this section.

4. The indicator light will flash slowly at first and then

rapidly after HomeLink

®

successfully receives the

frequency signal from the hand-held transmitter.
Release both buttons.

5. Press and hold the newly-trained HomeLink

®

button

and observe the indicator light.

If the indicator light stays on constantly,
programming is complete and your device should
activate when the HomeLink

®

button is pressed

and released.

To program the remaining two HomeLink

®

buttons,

begin with Step 2 under “Programming HomeLink

®

.”

Do not repeat Step 1 as this will erase all of the
programmed channels.

If the indicator light blinks rapidly for two seconds
and then turns to a constant light, continue with
Steps 6 through 8 following to complete the
programming of a rolling-code equipped device
(most commonly, a garage door opener).

6. Locate in the garage, the garage door opener

receiver (motor-head unit). Locate the “Learn”
or “Smart” button. This can usually be found
where the hanging antenna wire is attached to the
motor-head unit.

7. Firmly press and release the “Learn” or “Smart”

button. The name and color of the button may
vary by manufacturer.

You will have 30 seconds to start Step 8.

8. Return to the vehicle. Firmly press and hold the

programmed HomeLink

®

button for two seconds,

then release. Repeat the press/hold/release
sequence a second time, and depending on the
brand of the garage door opener (or other rolling
code device), repeat this sequence a third time
to complete the programming.

HomeLink

®

should now activate your rolling-code

equipped device.

To program the remaining two HomeLink

®

buttons,

begin with Step 2 of “Programming HomeLink

®

.” You do

not want to repeat Step 1, as this will erase all
previous programming.

2-35

Summary of Contents for MONTE CARLO 2005













































































































































































































































































































































































































Reviews:

No comments

Related manuals for MONTE CARLO 2005

A-Tach Mounts 50131 Instructions preview
50131
Brand: A-Tach Mounts Pages: 2
B-Speech B-Speech Prim Manual preview
B-Speech Prim
Brand: B-Speech Pages: 18
Kargo Master 40131 Installation Manual preview
40131
Brand: Kargo Master Pages: 5
Lancia THESIS CONNECT Owner'S Handbook Manual preview
THESIS CONNECT
Brand: Lancia Pages: 386
Webasto Transit Vancouver Wagon Manual preview
Transit Vancouver Wagon
Brand: Webasto Pages: 44
CARRYBOY CB-796IG2-CIGD-R Installation Manual preview
CB-796IG2-CIGD-R
Brand: CARRYBOY Pages: 4
GMC 2012 Terrain Owner'S Manual preview
2012 Terrain
Brand: GMC Pages: 428
UAZ 2001 ???-3741 Instruction Manual preview
2001 ???-3741
Brand: UAZ Pages: 112
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Brand: SilverLeaf Electronics Pages: 16
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Brand: Mercedes-Benz Pages: 91
POOL-LINE 110050 Assembly Instructions preview
110050
Brand: POOL-LINE Pages: 2
Prorack K374 Manual preview
K374
Brand: Prorack Pages: 14
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Brand: Cadillac Pages: 19
Edelbrock 8135 Installation Instructions preview
8135
Brand: Edelbrock Pages: 4
Westin 33-1920 Instructions preview
33-1920
Brand: Westin Pages: 3
Hamron 012463 Operating Instructions Manual preview
012463
Brand: Hamron Pages: 6
Connects2 CTQIAU03 Installation & User Manual preview
CTQIAU03
Brand: Connects2 Pages: 2
Prorack K138 Fitting Instructions Manual preview
K138
Brand: Prorack Pages: 14

Brands by name

Popular brands

Load more brands