manualshive.com logo in svg

Chevrolet 2008 Colorado, Owner'S Manual

The Chevrolet 2008 Colorado Owner's Manual is a comprehensive guide that provides detailed information and instructions on operating and maintaining your vehicle. This manual is available for download, absolutely free, from manualshive.com, ensuring you have the essential resource at your fingertips.

Share
Download
background image

Washing Your Vehicle

The best way to preserve your vehicle’s finish is to keep
it clean by washing it often.

Notice: Certain cleaners contain chemicals that can
damage the emblems or nameplates on your
vehicle. Check the cleaning product label. If it states
that it should not be used on plastic parts, do not
use it on your vehicle or damage may occur
and it would not be covered by the warranty.

Do not wash the vehicle in direct sunlight. Use a
car washing soap. Do not use cleaning agents that are
petroleum based or that contain acid or abrasives,
as they can damage the paint, metal or plastic on your
vehicle. Approved cleaning products can be obtained
from your dealer/retailer. See Vehicle Care/Appearance
Materials on page 5-114.

Follow all manufacturers’ directions regarding correct
product usage, necessary safety precautions and
appropriate disposal of any vehicle care product.

Rinse the vehicle well, before washing and after to
remove all cleaning agents completely. If they are
allowed to dry on the surface, they could stain.

Dry the finish with a soft, clean chamois or an all-cotton
towel to avoid surface scratches and water spotting

High pressure car washes may cause water to enter the
vehicle. Avoid using high pressure washes closer
than 12 inches (30 cm) to the surface of the vehicle.
Use of power washers exceeding 1,200 psi (8 274 kPa)
can result in damage or removal of paint and decals.

Cleaning Exterior Lamps/Lenses

Use only lukewarm or cold water, a soft cloth and a
car washing soap to clean exterior lamps and lenses.
Follow instructions under Washing Your Vehicle on
page 5-110.

5-110

Summary of Contents for 2008 Colorado

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Colorado

Paccar DAF POWERCHOICE 250A Installation Manual preview
DAF POWERCHOICE 250A
Brand: Paccar Pages: 20
Pyle PLCMRV8B Black User Manual preview
PLCMRV8B Black
Brand: Pyle Pages: 4
AA Products SR-A260 Instruction Manual preview
SR-A260
Brand: AA Products Pages: 4
Thule Kit 2161 Fitting Instructions preview
Kit 2161
Brand: Thule Pages: 2
Hyundai SANTA FE 2020 Getting Started Manual preview
SANTA FE 2020
Brand: Hyundai Pages: 19
Car-Systems Parktronic system Volkswagen Golf MK7 Assembly Manual preview
Parktronic system Volkswagen Golf MK7
Brand: Car-Systems Pages: 10
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Brand: Saturn Pages: 440
Rugged Ridge 11232.20 Quick Start Manual preview
11232.20
Brand: Rugged Ridge Pages: 2
Waeco Perfect Fit MBM120 Installation Instructions preview
Perfect Fit MBM120
Brand: Waeco Pages: 3
Or-Fab HD Bumper Installation Instructions preview
HD Bumper
Brand: Or-Fab Pages: 4
PUTCO 1951 Series Instruction Manual preview
1951 Series
Brand: PUTCO Pages: 3
Honda 2010 Accord Coupe Owner'S Manual preview
2010 Accord Coupe
Brand: Honda Pages: 410
Ford transit connect 2012 User Manual preview
transit connect 2012
Brand: Ford Pages: 299
Charge Amps Halo Pole Mount Manual preview
Halo Pole Mount
Brand: Charge Amps Pages: 14
Honda 2001 Accord Sedan Owner'S Manual preview
2001 Accord Sedan
Brand: Honda Pages: 372
Imiola HAK-POL F/005 Fitting Instruction preview
F/005
Brand: Imiola HAK-POL Pages: 3
Istar PI00670 Instruction Manual preview
PI00670
Brand: Istar Pages: 6
iDataLink BLADE-AL-HK4-EN Install Manual preview
BLADE-AL-HK4-EN
Brand: iDataLink Pages: 35

Brands by name

Popular brands

Load more brands