Chevrolet 2008 Colorado Owner'S Manual Download Page 364 | Manualshive

Page: 364 / 440

background image

9. Position the center lift point of the jack under the

center of the spare tire.

10. Turn the wrench clockwise to raise the jack until it

lifts the end fitting.

11. Continue raising the jack until the spare tire stops

moving upward and is held firmly in place.
The secondary latch has released and the spare
tire is balancing on the jack.

12. Lower the jack by turning the wheel wrench

counterclockwise. Keep lowering the jack until the
spare tire slides off the jack or is hanging by
the cable.

{

CAUTION:

Someone standing too close during the
procedure could be injured by the jack.
If the spare tire does not slide off the jack
completely, make sure no one is behind you or
on either side of you as you pull the jack out
from under the spare.

5-98

«
...
362
363
364
365
366
...
»

Summary of Contents for 2008 Colorado

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Colorado

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: Daihatsu Pages: 340

Brand: Daihatsu Pages: 41

Brand: Daihatsu Pages: 268

Brand: Kargo Master Pages: 13

Brand: Kargo Master Pages: 21

Brand: Kargo Master Pages: 4

Multiple G9F18 AU000

Brand: Genesis Pages: 3

MagicComfort MSH200

Brand: Waeco Pages: 108

Brand: Tusk Pages: 2

Brand: P-Invent Pages: 4

Brand: Kuda Pages: 2

Brand: Kargo Master Pages: 19

PRIME DESIGN VBR3-FT31B

Brand: Safe Fleet Pages: 12

SANICON TURBO 300

Brand: Thetford Pages: 25

Brand: Honda Pages: 569

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands