manualshive.com logo in svg

Chevrolet 2008 Colorado, Owner'S Manual

Share
Download
Chevrolet 2008 Colorado Owner'S Manual Download Page 178

LOW TIRE

This message displays if a low tire pressure is detected
in any of the vehicle’s tires. Press and release the reset
stem to acknowledge the message and clear it from the
display. The message appears at each ignition cycle until
the tires are inflated to the correct inflation pressure.
See Tires on page 5-59 and Inflation - Tire Pressure on
page 5-66 for more information on tires and the correct
inflation pressures.

LOW TRAC (Traction)

If your vehicle has the Traction Control System (TCS),
this message displays when a low traction condition
is detected. See Traction Control System (TCS)
on page 4-5 for more information. Press and release
the reset stem to acknowledge the message and clear
it from the display.

OIL

This message displays when the oil pressure is low.
See Oil Pressure Light on page 3-36 and Engine Oil
on page 5-15 for more information.

PARK BRK (Brake)

This message displays when the parking brake is set.
See Parking Brake on page 2-32 and Brake System
Warning Light on page 3-31 for more information. The
message clears from the display after the parking brake
is released or by pressing and releasing the reset stem.

REDUCED POWER

This message displays when the vehicle’s engine power
is reduced. Reduced engine power can affect the
vehicle’s ability to accelerate. If this message is on, but
there is no reduction in performance, proceed to your
destination. The performance may be reduced the next
time the vehicle is driven. The vehicle may be driven at a
reduced speed while this message is on, but acceleration
and speed may be reduced. Anytime this message stays
on, the vehicle should be taken to your dealer/retailer for
service as soon as possible. Press and release the reset
stem to acknowledge the message and clear it from the
display.

3-44

Summary of Contents for 2008 Colorado

























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands