Chevrolet 2008 Colorado Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 440

background image

Q:

If I am a good driver, and I never drive far from
home, why should I wear safety belts?

A:

You may be an excellent driver, but if you are in a
crash — even one that is not your fault — you and
your passenger(s) can be hurt. Being a good driver
does not protect you from things beyond your
control, such as bad drivers.

Most accidents occur within 25 miles (40 km)
of home. And the greatest number of serious
injuries and deaths occur at speeds of less than
40 mph (65 km/h).

Safety belts are for everyone.

How to Wear Safety Belts Properly

This section is only for people of adult size.

Be aware that there are special things to know about
safety belts and children. And there are different rules for
smaller children and babies. If a child will be riding in your
vehicle, see Older Children on page 1-33 or Infants and
Young Children on page 1-36. Follow those rules for
everyone’s protection.

It is very important for all occupants to buckle up.
Statistics show that unbelted people are hurt more often
in crashes than those who are wearing safety belts.

Occupants who are not buckled up can be thrown out
of the vehicle in a crash. And they can strike others
in the vehicle who are wearing safety belts.

First, before you or your passenger(s) wear a safety
belt, there is important information you should know.

Sit up straight and always keep your feet on the floor in
front of you. The lap part of the belt should be worn low
and snug on the hips, just touching the thighs. In a crash,
this applies force to the strong pelvic bones and you
would be less likely to slide under the lap belt. If you slid
under it, the belt would apply force on your abdomen.
This could cause serious or even fatal injuries.

1-17

«
...
19
20
21
22
23
...
»

Summary of Contents for 2008 Colorado

























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2008 Colorado

Brand: iArmor Pages: 6

Brand: Suzuki Pages: 353

Brand: Torklift Pages: 16

Brand: Kolpin Outdoors Pages: 6

Brand: Schartec Pages: 2

Brand: Oldsmobile Pages: 2

Brand: Ford Pages: 256

Brand: EUFAB Pages: 12

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

Brand: Oldsmobile Pages: 354

Brand: EUFAB Pages: 20

Brand: QA1 Pages: 3

Prestige 128-8602

Brand: Audiovox Pages: 8

Brand: Westin Pages: 3

CHALLENGER HELLCAT 2017

Brand: Dodge Pages: 484

Brand: EUFAB Pages: 12

Brand: STO N SHO Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands