manualshive.com logo in svg

Chevrolet 2008 Colorado, Owner'S Manual

Share
Download
Chevrolet 2008 Colorado Owner'S Manual Download Page 277

Hood Release

To open the hood, do the following:

1. Pull the handle with

this symbol on it. It is
located inside the
vehicle on the lower
left side of the
instrument panel.

2. Release the secondary latch on the hood. It is

located below the front center of the hood.

3. Lift the hood.

4. Release the hood prop from its retainer and put the

hood prop into the slot in the hood.

Before closing the hood, be sure all the filler caps are
on properly. Then lift the hood to relieve pressure on the
hood prop. Remove the hood prop from the slot in the
hood and return the prop to its retainer. Lower the hood
10 to 12 inches (25 to 30 cm) above the vehicle and
release it to latch fully. Check to make sure the hood is
closed and repeat the procedure if necessary.

5-11

Summary of Contents for 2008 Colorado

























































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands