background image

12

TRANSPORTATION & STORAGE

  WARNING- TRANSPORT AND STORE TRAP 

WITH THE MAINSPRING REMOVED AND OUT OF 

CHILDREN’S REACH. UNINTENTIONAL FIRING OF 

THE TRAP CAN CAUSE SERIOUS INJURY OR DEATH 

FROM BEING STRUCK BY THE THROWING ARM.

1.  Ensure throwing arm is in the 9 o’clock to 12 o’clock 

(uncocked) position.

2.  Carefully release spring tension by loosening the 

10mm hex nut. 

3.  Remove the mainspring.
4.  Once mainspring is removed, manually rotate 

throwing arm to 6 o’clock position. 

5.  If necessary, detach throwing arm path indicator 

and supports. 

6.  Store trap indoors away from the elements and 

out of children’s reach.

TROUBLESHOOTING

SYMPTOM -

TRIGGER MALFUNCTION

Corrective action:

•  Trigger Springs missing or broken - replace

•  Tab on end of Throwing Arm missing or damaged - 

replace Throwing Arm.

SYMPTOM -

TRIGGER DIFFICULT TO RELEASE

Corrective action:

•  Lubricate Trigger Mounting Rivets and Trigger Post,

•  Cock trap with less force (or more slowly).

SYMPTOM -

RATCHET MECHANISM MALFUNCTIONS

Corrective action:

•  Inspect Ratchet Springs - replace if bent, rusted, or 

broken

•  Clean and lubricate Ratchet Pawls.

SYMPTOM -

BROKEN, ERRATIC, OR UNSTABLE TARGETS 

Corrective action:

• 

If rubber strip of Flight Control Rail is damaged, replace 

Flight Control Rail Assembly.

• 

Check position of Flight Control Rail. Use lowest holes 

for battues and rabbits - top holes for all other targets.

• 

Decrease Mainspring Tension.

• 

Adjust tension of Target Clip. The Target Clip should 

press against the target just enough to hold it in place

• 

Make sure lip of target is tucked under Flight Control 

Rail.

• 

If target jars loose before fi ring, cock trap with less force.

• 

Inspect targets for fi ne cracks.

• 

Bent or cracked Throwing Arm – replace.

• 

Make sure all screws and bolts are tight on the Throwing 

Arm and Flight Control Rail.

SYMPTOM -

“TAILING TARGET” (Target tilts to right or left) 

Corrective action:

•  Check if trap is placed on a level surface.

SYMPTOM -

FLIGHT DISTANCE GRADUALLY DECREASES

Corrective action:

•  Increase Mainspring tension.

•  Replace Mainspring Assembly.

CONTACT INFORMATION

Champion Traps and Targets

1 Vista Way

Anoka, MN 55303

Toll Free: (800) 379-1732

Website: www.championtarget.com

Email: [email protected]

Summary of Contents for 40903





























Reviews: