Chamberlain MotorLift500, Instructions Manual

Page: 16 / 36

5-GB
Replacement Parts
(1) 41A5644 Trolley with Chain/Cable Assy.
(2) 41A5674 Head Only
(3) 41A5643 Hardware Bag
(4) 012B0905 Door Bracket
012B0906
(5) 012C0788 Header Bracket
(6) 012C0908 Rail End Piece
(7) 41A5675 Rail Hardware
(8) 41A5676 Rail Sections
Specifications
FOR USE IN THE EU
Input Voltage . . . . . . . . . . . .230 VAC 50/60 Hz
Max. Pull force . . . . . . . . . .600N
Rated Power Input . . . . . . .85 Watts
Rated Load . . . . . . . . . . . . .3.0 Nm
Standby Power . . . . . . . . . .9 Watts
Max. Door Weight . . . . . . . .60kg
Motor
Type . . . . . . . . . . . . . . . . . .63:1 Worm Gear Reduction
Volts . . . . . . . . . . . . . . . . . . .24VDC
Drive Mechanism
Length of Travel . . . . . . . . .2.3M
Travel Rate . . . . . . . . . . . . .8cm/sec
Lamp . . . . . . . . . . . . . . . . . .24V 21 Watts
Safety
Electronic . . . . . . . . . . . . . .Auto-Force Adjustment
Electrical . . . . . . . . . . . . . . .Thermal Fuse in Transformer
Limit Adjustment . . . . . . . . .Manual
Dimension
Length (Overall) . . . . . . . . .2.75m
Headroom Required . . . . . .30mm
Hanging Weight . . . . . . . . . .9kg
Receiver Code Registers
Rolling Code . . . . . . . . . . . .8
Dip Switch . . . . . . . . . . . . . .1
Keypad . . . . . . . . . . . . . . . .1
Operating Frequency . . . . .433.92MHz
24
Wiring the Multi-Function Door Control Panel
and the Lighted Door Control Button (Optional)
Locate any Wall Mounted Door Control where the garage door is
visible, away from door and door hardware, at a minimum height of
1.5m. fasten the child warning label on the wall near the Door
Control.
There are 2 screw terminals (1) on the back of the Door Control (2). Strip
about 6mm of insulation from bell wire (4). Separate wires enough to
connect the white/red wire to terminal screw 1 and the white wire to
terminal screw (1).
Lighted Door Control Button: Fasten to an inside garage wall with
sheet metal screws (3) provided with Lighted Push Button. Drill 4mm
holes and use anchors (6) if installing into drywall or concrete. A
convenient place is beside the service door and
out of reach of
children.
Multifunction Door Control:
Insert a small flat head screwdriver into the
top of the Wall Control (10), gently pry the cover off. Fasten to an inside
garage wall with sheet metal screws (8) as follows:
• Install bottom screw, allowing 3mm to protrude from the wall.
• Position bottom of door control over screw head and adjust for snug fit.
• Install top screw with care to avoid cracking plastic housing.
Do not
over tighten.
• Replace cover by inserting bottom tabs (9) and snapping into place. To
remove cover after mounting, gently pry at top with paper clip or small
flat head screwdriver.
Run the bell wire up the wall and across the ceiling to the garage door
opener. Use insulated staples (5) to secure wire.
The opener Quick-Connect Terminals (7) are located in the recess next
to the learn button on the left side panel. Insert bell wire into holes in the
Quick Connect Terminals as follows: Red/White to Red and White to
White.
Accessories
(1) Model 84330EML Single Function Remote Control
(2) Model 84333EML 3-Function Remote Control
(3) Model 84335EML 3-Function Mini Remote Control
(4) Model 770EML The Protector System
(5) Model 8747EML Wireless Keyless Entry Keypad
(6) Model 845EML Multi-Function Door Control Panel
(7) Model 75EML Lighted Door Control Button
(8) Model 760EML Outside Keylock
(9) Model 1702EML Outside Quick Release
23
22
D e c l a r a t i o n o f C o n f o r m i t y
The undersigned, hereby declare that the equipment specified, and all
accessories, conforms to the Directives and Standards stated.
Model:...........................................................................................ML500
89/336/EEC
73/23/EEC
1999/5/EC
EN55014-1 (2000), EN55014-2 (1997), EN61000-3-2 (2000), EN61000-3-3
(1995), EN 301 489-3 (V1.3.1), EN 300 220-3 (V1.1.1), EN60335-1 (1994),
and EN60335-2-95 (2000)
D e c l a r a t i o n o f I n c o r p o r a t i o n
A power door operator, in combination with a Garage Door must be installed
and maintained according to all the Manufacturer’s instructions, to meet the
provisions of EN12453, EN13241-1 and Machinery Directive, 89/392/EEC.
B. P. Kelkhoff
Manager, Regulatory Affairs
Chamberlain GmbH
D-66793 Saarwellingen
July, 2007