background image

1-28 

Fuel Tanks 

50. 

Fuel is carried in two bladder style vented tanks (one in each wing). Fuel capacities 

(total and useable fuel) are provided in Figure 1-3. Tank drains at the rear, inboard corner of 
each tank are provided for fuel sampling.  

 

 

 

 

 

 

 

Figure 1-33 Fuel Tank Drain 

Fuel Strainer 

51. 

A fuel strainer is installed in the engine compartment to filter out any remaining water or 

contaminants from the fuel before it reaches the fuel injection system. The fuel strainer drain 
valve is adjacent to the oil dip stick and is accessed through a door on the left side of the 
engine cowling. During the pre-flight inspection, the strainer should be opened to drain for 
approximate 4 seconds to clear any water or sediment.  

 

 

 

 

 

 

 

 

 

Figure 1-34 Oil Dip Stick and Fuel Strainer Drain 

Fuel Vent System 

52. 

The left tank is fitted with a vent line incorporating a check valve which protrudes from 

the bottom of the left wing near the strut attachment point. Venting of the right tank is 
accomplished through an interconnecting vent line.  

Summary of Contents for 182

































































































































































Reviews: