Certikin Dolphin Sport Manual Download Page 29

Page: 29 / 32

The build process continued -

Steps 61 to 72 are for Fastlane installation only

STEP 71

Replace grill and attach the top to complete.closed position.

STEP 72

Attach the hose ends to the hydrolic pump (hose ends are

colour coded). Refer to the Fastlane manual for the start up

procedure.

STEP 73

Go around the pool gently tightening the nuts and checking

that the pool timbers are level.

Do not over tighten.

STEP 74

While the pool is filling with water, place the timber top

surround into position around the pool.

STEP 75

Line up all 8 corners with an even overlap of the timber. Make

use of the clamps to help hold the timbers into position. Using

straps as per step 31, will also make this process easier.

STEP 76

When all of the top timbers are in position start by drilling a

6mm pilot hole into the timber underneath.

Summary of Contents for Dolphin Sport

































Search results

Summary of Contents for Dolphin Sport

Reviews:

Related manuals for Dolphin Sport

Brands by name

Popular brands

Certikin Dolphin Sport, Manual

Search results

Summary of Contents for Dolphin Sport

Reviews:

Related manuals for Dolphin Sport

Brands by name

Popular brands