Certikin Dolphin Sport Manual Download Page 30

Page: 30 / 32

The build process continued

STEP 77

Insert the 10mm coach screws and washers and gently tighten

down with the socket wrench. Repeat around the pool. Once

complete fit the chrome caps.

STEP 78

Select the side where the steps are to be positioned.

Stand the step flange brackets on the top surround at 500mm

centres and mark the position of the holes.

STEP 79

Place the flange bracket so that the two holes shown are over the

96mm x 96mm timber under the top.

STEP 80

Drill 6mm pilot holes through the timber. Tighten down with

M10 x 100mm coach screws.

Place the flange under the top

STEP 81

Place the stainless steel covers and then assemble and fit the
steps. Assembly instructions for the steps are are in the steps

box.

STEP 82

Screw in the two eye screws into the top of the

underside of the wodden pool steps as shown above.

Summary of Contents for Dolphin Sport

































Search results

Summary of Contents for Dolphin Sport

Reviews:

Related manuals for Dolphin Sport

Brands by name

Popular brands

Certikin Dolphin Sport, Manual

Search results

Summary of Contents for Dolphin Sport

Reviews:

Related manuals for Dolphin Sport

Brands by name

Popular brands