Century Helicopter Products Predator Casser Manual Download Page 3 | Manualshive

Page: 3 / 59

background image

Predator Gasser NX

Page 3

CN2050

PADDLE GAUGE

CN2034A

BALL LINK PLIERS

HOBBY KNIFE

RECEIVER BATTERY

SERVOS X 5

ZIP TIES

4-WAY WRENCH

GYRO

6 CHANNEL RECEIVER

(MINIMUM)

HOBBY SCISSORS

METRIC RULER OR

SIMILAR MEASURING

DEVICE

CN2017

HEX DRIVERS

1.5, 2.0, 2.5, 3.0 & 4.0

6 CHANNEL

CCPM TRANSMITTER

(MINIMUM)

CN2027

G-FORCE PITCH GAUGE

CN2051

ACCURATECH BLADE BAL-

ANCER V.2

CN2255

CONTROL ROD

SETUP GAUGE

NEEDLE NOSE

PLIERS

SYNTHETIC

OIL/GREASE

1.000

87 TO 92 OCTANE

GASOLINE

710MM TO 830MM

CARBON FIBER BLADES

23CC TO 26CC

GASOLINE ENGINE

CN3069B

SPEED TORPEDO

V.4 GASSER TUNED

MUFFLER

2-STROKE

MOTOR OIL

CA GLUE

DREMEL TOOL

OR SIMILAR

REQUIRED ITEMS

Century Helicopter Products warranties that the Products purchased (the “Product”) will be free from defects in materials and workman-
ship 30 days from the date of purchase by the Purchaser.

Warranty Period

(a) This warranty is limited to the original customer (“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those Products purchased
from an authorized Century Helicopter Products dealer. Third party transactions are not covered by this warranty. Proof of purchase is
required for warranty claims. Further, Century Helicopter Products reserves the right to change or modify this warranty without notice
and disclaims all other warranties, express or implied.
(b) Limitations- CENTURY HELICOPTER PRODUCT MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-
INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER ACKNOWLEDG-
ES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S
INTENDED USE.
(c) Purchaser Remedy- Century Helicopter Products’s sole obligation hereunder shall be that Century Helicopter Products will, at its
option, (i) repair or (ii) replace, any Product determined by Century Helicopter Products to be defective. In the event of a defect, these
are the Purchaser’s exclusive remedies. Century Helicopter Products reserves the right to inspect any and all equipment involved in
a warranty claim. Repair or replacement decisions are at the sole discretion of Century Helicopter Products. This warranty does not
cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any
part of the Product. This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by
anyone other than Century Helicopter Products. Return of any goods by Purchaser must be approved by Century Helicopter Product s
before shipment.

Limited Warranty

1.000

CN2031

«
1
2
3
4
5
...
»

Summary of Contents for Predator Casser




























































Reviews:

No comments

Related manuals for Predator Casser

Brand: GAME OF BRICKS Pages: 47

Brand: T&J Pages: 11

30 model building set

Brand: KNEX Pages: 24

Where Can We Go Wheel

Brand: VTech Pages: 10

4-6-2 Pacific Steam Locomotive

Brand: Rail King Pages: 29

Brand: Viessmann Pages: 2

Brand: Gyros Pages: 7

STAR WARS 10221

Brand: LEGO Pages: 228

Brand: BLOTZ Pages: 2

Brand: PARKZONE Pages: 12

Star Wars 75060

Brand: LEGO Pages: 307

Brand: Hornby Pages: 2

Call of Duty DPW84

Brand: Mega Construx Pages: 24

Clean Sweep Learning Caddy

Brand: LeapFrog Pages: 16

Brand: Fly Fly Hobby Pages: 9

Premier T-1 Reading Steam Locomotive

Brand: M.T.H. Pages: 29

TOCA LIFE BOX SUSHI STATIONERY

Brand: Sago Pages: 6

Brand: POLA G Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands