background image

- 14 -

SDOPD

OPTIONS AND FEATURES

16. Auto Close

Auto Close can enhance the security of your property by ensuring that your garage door is never

unintentionally left open.

Auto Close will automatically close the garage door;

i. 3 sec after reaching the fully open position - provided that a person or object

has

passed through

the Safety Beams within the Delay Time, or

ii. upon expiry of the user selected delay time – provided that a person or object

has not

passed

through the Safety Beams within the Delay Time.

Note: Auto Close will function only when used in conjunction with Safety Beams. (Refer sec.23)

Enabling

The function select Dip Switches are contained within the rear cover of the AGDO

Select Dips 1 & 2 to the “ON” position. (Fig.11)

Delay Time Selection

Auto Close delay time may be configured according to the following table;

Delay (sec)

Dip No. 3

Dip No. 4

15

off

off

30

on

off

45

off

on

60

on

on

17. Courtesy Lamp

The in built Courtesy Lamp will illuminate each time the AGDO is activated and then switch off

automatically 3 min after receiving the last Hand Transmitter or run signal.

Bulb Replacement

Remove Lamp Cover by lifting at the 2 uppermost inside edges.

Remove bulb by turning it in an anti-clockwise direction.

Replace bulb with identical 60W (maximum) Edison Screw

rough construction

.

Important Note: Replacing the bulb with a model greater than 60W will cause the light cover

and/or main cover to melt!

18. Dip Switches

The Dip Switches located within the back cover of the AGDO (Fig.11) enable or disable specific

functionality.

By reading through the section titled “Options and Features” the AGDO’s functionality can be

customized to individual requirements.

The functions of the Dip Switches are described in the following table;

Function

Dip No.

Dip Position

Reference

Safety Beams (SB) - Enable

1

ON

Sec.23

Auto Close (AC) - Enable

1 & 2

ON

Sec.23

Auto Close Delay Time

3 & 4

Varies

Sec.16

Summary of Contents for SDO-10




















Reviews: