Cedar Summit F25720 Installation And Operating Instructions Manual Download Page 51

Page: 51 / 108

Pre-drill all holes using a 3/16” drill bit before

installing the lag screws.

To adjust for uneven ground, raise or lower the

(170) Support Cross on the (162) SW Post. Make sure

the Support Cross is level prior to attaching with the lag

screws. (fig. 17.1 and 17.2)

Place (170) Support Cross between (162) SW

Posts at the previously determined spot and fasten with

1 (LS9) 5/16 x 4-3/4” Lag Screw (with flat washer) per

side. (fig. 17.2 and 17.3)

Notice one side is fastened

on the outside and one on the inside. It is important

that each side is positioned exactly the same as the

diagram. (fig. 17.3) Tighten the lag screw when

you are sure (170) Support Cross is level.

Attach 1 (WB8) 5/16 x 2-3/8” Wafer Bolt (with flat

washer and t-nut) to (170) Support Cross through

the middle hole. (fig. 17.2 and 17.3)

IMPORTANT!

MAKE SURE THE BOLT IS ATTACHED TO MINIMIZE

CHECKING OF WOOD.

Step 17: Attach Cross Support

Fig. 17.1

5/16” Flat

Washer

5/16” T-Nut

Fig. 17.3

Hardware

Wood Parts

2 x

5/16 x 4-3/4” Lag Screw

(5/16” flat washer)

1 x

5/16 x 2-3/8” Wafer Bolt

(5/16” flat washer, 5/16” t-nut)

WB8

LS9

1 x

Support Cross 2-1/2 x 3 x 51”

170

162

LS9

WB8

5/16” Flat

Washer

5/16” Flat

Washer

170

Fig. 17.2

[email protected]

Summary of Contents for F25720













































































































Search results

Summary of Contents for F25720

Reviews:

Related manuals for F25720

Brands by name

Popular brands

Cedar Summit F25720, Installation And Operating Instructions Manual

Search results

Summary of Contents for F25720

Reviews:

Related manuals for F25720

Brands by name

Popular brands