manualshive.com logo in svg

Cedar Summit F25720, Installation And Operating Instructions Manual

Share
Download
Cedar Summit F25720 Installation And Operating Instructions Manual Download Page 27

C:

  From inside the assembly, tight to both (040) Panel Slide End and (050) SW Wall Panel, halfway up the 

assembly, 5/8” below the panel, loosely attach 1 (061) Side Joist to (041) Narrow Panel Back and (052) Wall 

Panel Back with 3 (WB10) 5/16 x 2-5/8” Wafer Bolts (with flat washer and t-nut).  Bolts are installed from inside 

the assembly.  Make sure (061) Side Joist is level then attach with 2 (S3) #8 x 2-1/2” Wood Screws and tighten 

bolts.  (fig. 6.3, 6.4 and 6.5)

D:

  Repeat Step C to attach 1 (061) Side Joist to (042) Narrow Front Panel and (051) Panel Front Wall.   

(fig. 6.3, and 6.4)

4 x 

#8 x 2-1/2” Wood Screw

6 x 

5/16 x 2-5/8” Wafer Bolt

 

(5/16” flat washer, 5/16” t-nut)

Fig. 6.3

Hardware

Inside View

Step 6:  Join Swing and Slide Wall Assemblies 

Part 2

S3

2 x 

Side Joist 2 x 2 x 63”

Wood Parts

061

Fig. 6.4

5/16” Flat 

Washer

WB10

5/16” 

T-Nut

Fig. 6.5

061

Panel

5/8”

A

A

Tight

Tight

WB10

S3

S3

052

041

061

050

040

 27 

        

[email protected]

   

Summary of Contents for F25720













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands