Cedar Summit F25720 Installation And Operating Instructions Manual Download Page 91

Page: 91 / 108

Step 43: Attach Transom Assembly

Part 1

Place 1 Transom Assembly on both (051) Front Wall Panel and (052) Back Wall Panel so they are tight

to (400) Swing Top and (410) Wall Supports. From the outside attach each Transom Assembly to (410) Wall

Supports with 2 (S3) #8 x 2-1/2” Wood Screws per assembly. (fig. 43.1)

From the inside attach (410) Wall Supports to each Transom Assembly and both (051) Front Wall Panel and

(052) Back Wall Panel with 4 (S3) #8 x 2-1/2” Wood Screws per support. (fig. 43.2)

From the inside attach each (394) Wall Tie to both (051) Front Wall Panel and (052) Back Wall Panel with 2

(S11) #8 x 2” Wood Screws per board. (fig. 43.2)

Fig. 43.2

Inside View

Fig. 43.1

Hardware

12 x

#8 x 2-1/2” Wood Screw

4 x

#8 x 2” Wood Screw

410

400

Transom

Assembly

x 2 per Transom

Assembly

(both

supports)

410

051

Transom

Assembly

052

051

S11

394

[email protected]

Summary of Contents for F25720













































































































Search results

Summary of Contents for F25720

Reviews:

Related manuals for F25720

Brands by name

Popular brands

Cedar Summit F25720, Installation And Operating Instructions Manual

Search results

Summary of Contents for F25720

Reviews:

Related manuals for F25720

Brands by name

Popular brands