Cedar Summit F25720 Installation And Operating Instructions Manual Download Page 24

Page: 24 / 108

1 x

End Slide Panel 1-1/4 x 37 x 92”

1 x

Narrow Panel Back 1-1/4 x 21-1/2 x 92”

1 x

Narrow Front Panel 1-1/4 x 21-1/2 x 92”

Wood Parts

040

Step 4: Slide Wall Assembly

Place (041) Narrow Panel Back against the left side of (040) End Slide Panel noticing panel orientation. The

tops and bottoms of the panels should be flush and panels square. Pre-drill with a 3/16” drill bit, then fasten

(041) Narrow Panel Back to (040) End Slide Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (fig. 4.1 and 4.2)

Place (042) Narrow Front Panel against the right side of (040) End Slide Panel noticing panel orientation.

The tops and bottoms of the panels should be flush and panels square. Pre-drill with a 3/16” drill bit, then fasten

(040) Slide End Panel to (042) Narrow Front Panel with 4 (WL5) 1/4 x 2-1/2” Wafer Lags. (fig. 4.1 and 4.3)

Fig. 4.2

Fig. 4.1

Hardware

8 x

1/4 x 2-1/2” Wafer Lag

WL5

041

042

Notice (041) Narrow

Back Panel overlaps

(040) Slide End Panel

Fig. 4.3

WL5

Flush

040

041

WL5

042

040

Notice (040) Slide End

Panel overlaps (042)

Narrow Front Panel

Flush

040

Flush

[email protected]

Summary of Contents for F25720













































































































Search results

Summary of Contents for F25720

Reviews:

Related manuals for F25720

Brands by name

Popular brands

Cedar Summit F25720, Installation And Operating Instructions Manual

Search results

Summary of Contents for F25720

Reviews:

Related manuals for F25720

Brands by name

Popular brands