manualshive.com logo in svg

Cedar Summit F25720, Installation And Operating Instructions Manual

Share
Download
Cedar Summit F25720 Installation And Operating Instructions Manual Download Page 47

Step 15:  Swing Beam Assembly 

Part 2

Hardware

E:

  On the Fort End of (150) Engineered SW Beam attach 2 Heavy Flat Brackets with 2 (G21) 5/16 x 3-3/4” 

Hex Bolts (with 2 flat washers and 1 lock nut). (fig. 15.6 and 15.7)

F:

  Place (151) SW Mount in between both Heavy Flat Brackets and place 1 Heavy L-Bracket against (150) 

Engineered SW Beam and (151) SW Mount.  Attach with 1 (G17) 3/8 x 6” Hex Bolt (with 2 flat washers, plastic 

formed washer and lock nut).  (fig. 15.8)

G:

  Attach (141) SW Mount to Heavy Flat Brackets with 2 (G21) 5/16 x 3-3/4” Hex Bolts (with 2 flat washers 

and 1 lock nut). (fig. 15.9)

4 x 

5/16 x 3-3/4” Hex Bolt 

 

(5/16” flat washer x 2, 5/16” lock nut)

1 x 

3/8 x 6” Hex Bolt 

 (3/8” flat washer x 2, plastic formed washer & 3/8” lock nut)

Other Parts

2 x Heavy Flat Bracket
1 x Heavy L-Bracket

G21

G17

Wood Parts

1 x 

SW Mount 4 x 4 x 16”

 

151

G21

150

5/16” Flat 

Washer

Fort End

5/16”  

Lock Nut

5/16” Flat 

Washer

Plastic 

Formed 

Washer

Heavy 

Flat 

Bracket

150

3/8”  

Lock Nut

Fig. 15.6

Fig. 15.7

Fig. 15.9

Fig. 15.8

G17

G21

151

150

151

5/16” Flat 

Washer

5/16” Flat 

Washer

5/16”  

Lock Nut

Heavy Flat 

Bracket

Heavy 

L-Bracket

3/8” Flat 

Washer

3/8” Flat 

Washer

 47 

        

[email protected]

   

Summary of Contents for F25720













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands