manualshive.com logo in svg

Cedar Summit F25720, Installation And Operating Instructions Manual

Share
Download
Cedar Summit F25720 Installation And Operating Instructions Manual Download Page 32

Step 8:  Attach Wall Tops

A:

  In the opening of (050) SW Wall Panel, from the inside, attach (080) SW Wall Top, tight to the corner of the 

panels with overhang facing in with 1 (S11) #8 x 2” Wood Screw at each end as shown in fig. 8.1 and 8.2.

B:

  In the opening of (040) Slide End Panel, from the inside, attach (081) Half Wall Top, tight to the corner of the 

panels with overhang facing in with 1 (S11) #8 x 2” Wood Screw at each end as shown in fig. 8.1 and 8.2.  

C:

  In the opening of (052) Wall Panel Back, from the inside, attach (082) Wall Top tight to the corner of the panel 

with overhang facing in with 1 (S11) #8 x 2” Wood Screw at each end as shown in fig. 8.1 and 8.3.

D:

  At the top of each slat, flush to the wall tops, attach 1 Corner Bracket using 3 (S37) #7 x 5/8” Pan Screws per 

bracket.  (fig. 8.1 and 8.3)  

Hardware

Fig. 8.1

Fig. 8.2

1 x 

SW Wall Top 5/4 x 3 x 33-1/2”

1 x 

Half Wall Top 5/4 x 3 x 33”

1 x 

Half Wall Top 5/4 x 3 x 39”

Wood Parts

080

4 x 

#8 x 2” Wood Screw

15 x  

#7 x 5/8” Pan Screw

S11

Inside View

Other Parts

5 x Corner Bracket

S37

081

082

Fig. 8.3

Inside View

B

D

C

B

D

C

B

D

C

040

052

Slat

Tight

081

080

082

050

S11

x 1 per end 

per board

Corner 

Bracket

Slat

S37

x 3 per 

bracket

 32 

        

[email protected]

   

Summary of Contents for F25720













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands