manualshive.com logo in svg

Cayman Systems 2E-W, User Manual

Share
Download
Cayman Systems 2E-W User Manual Download Page 7

 

Cayman 2E-W User’s Guide

Preface

November 2000

 

vii

 

 

 

Preface

 

About This 
Manual

 

This manual describes how to connect your Cayman 2E-W to your 
local area network (LAN) and wide area network (WAN) and how to 
configure it to function as a basestation for a wireless network and 
as an Ethernet router. You should read this manual completely before 
you connect your Cayman 2E-W to your Ethernet networks.

 

Who Should Read 
This Manual

 

This manual is intended for network or system administrators 
responsible for setting up and maintaining the hardware and 
software to connect Ethernet networks.

 

What This 
Manual Covers

 

Here’s what you will find in this manual:

 

 

Chapter 1, “About Your Cayman 2E-W,”

 

 presents an 

overview of the features, ports, and LEDs on your Cayman 2E-W.

 

 

Chapter 2, “Setting Up Your Cayman 2E-W,”

 

 describes how 

to unpack your Cayman 2E-W and how to connect and 
disconnect it from your Ethernet networks.

 

 

Chapter 3, “Configuring Your Cayman 2E-W,”

 

 describes 

how to use the web-based configuration interface to enter 
operating settings for your Cayman 2E-W.

Summary of Contents for 2E-W











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands