manualshive.com logo in svg

Cayman Systems 2E-W, User Manual

Share
Download
Cayman Systems 2E-W User Manual Download Page 26

Configuring Your Cayman 2E-W

Cayman 2E-W User’s Guide

3-4

November 2000

DHCP Mode 

(expert mode)

Off

 – Disable DHCP server.

Server

 – Cayman 2E-W uses 

DHCP to provide network 
configuration information to 
hosts on the Local Area 
Network. 

Server

 is the default 

setting.

Relay-agent

 – Cayman 2E-W 

forwards DHCP requests and 
responses to a remote DHCP 
server.

Start Address 

(expert mode)

The first IP address the 
Cayman 2E-W should assign 
for Dynamic Host Control 
Protocol clients. Applicable 
when DHCP Mode is set to 

Server

. Default is 

192.168.1.1

.

End Address 

(expert mode)

The last IP address the Cayman 
2E-W should assign for 
Dynamic Host Control 
Protocol clients. Applicable 
when DHCP Mode is set to 

Server

. Default is 

192.168.1.254

.

Lease Time 

(expert mode)

The time, in DD:HH:MM:SS 
format, for which a 
configuration issued by the 
Cayman 2E-W DHCP server is 
valid. Applicable when DHCP 
Mode is set to 

Server

. Default 

is 

00:01:00:00

 (one hour).

Server 
Address 

(expert mode)

The IP address the remote 
DHCP server to which your 
Cayman 2E-W will relay 
Dynamic Host Control 
Protocol address requests. 
Applicable when DHCP Mode 
is set to 

Relay-agent

.

Field Name

Description

Your 
Information

Summary of Contents for 2E-W











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands