manualshive.com logo in svg

Cayman Systems 2E-W, User Manual

Share
Download
Cayman Systems 2E-W User Manual Download Page 67

Cayman 2E-W User’s Guide

Using the Command Line Interface

November 2000

4-9

You can use the 

ping

 command to determine whether a hostname 

or IP address is already in use on your network. You cannot use the 

ping

 command to ping the Cayman 2E-W’s own IP address.

quit

Exits the Cayman 2E-W command line interface.

reset arp

Clears the Address Resolution Protocol (ARP) cache on your Cayman 
2E-W.

reset crash

Clears crash-dump information, which identifies the contents of the 
Cayman 2E-W registers at the point of system malfunction.

reset dhcp client release

Releases the DHCP lease the Cayman 2E-W is currently using to 
acquire the IP settings for its WAN (Ethernet B) port.

reset dhcp client renew

Renews the DHCP lease the Cayman 2E-W is currently using to 
acquire the IP settings for its WAN (Ethernet B) port. 

reset dhcp server

Clears the DHCP lease table in the Cayman 2E-W.

reset enet

Resets Ethernet statistics to zero.

reset ipmap

Clears the IP mapping table.

Summary of Contents for 2E-W











































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands