Cayman Systems 2E-W User Manual Download Page 119

Page: 119 / 170

Cayman 2E-W User’s Guide

Updating Your System Software

November 2000

6-1

Updating Your System
Software

Using the Home Page to Install a New Image

Using the Installer to Install a New Image

Using TFTP to Install a New Image

Using the Home
Page to Install a
New Image

You can install a new operating system image in your Cayman 2E-W
from the Home Page. To do so, the computer you are using to install
the new image must be connected to the LAN interface of the
Cayman 2E-W.

To install new operating system software in your Cayman 2E-W from
the Home Page:

Download the image from

http://www.cayman.com

and

copy it to a computer connected to the LAN side of your
Cayman 2E-W.

Open a web connection to your Cayman 2E-W from this
computer.

Summary of Contents for 2E-W











































































































































































Search results

Summary of Contents for 2E-W

Reviews:

Brands by name

Popular brands

Cayman Systems 2E-W, User Manual

Search results

Summary of Contents for 2E-W

Reviews:

Brands by name

Popular brands