Caviblaster 2040-D Operation & Maintenance Manual Download | Manualshive

Page: 32 / 38

background image

2040-D O&M Manual Ver 3.0 CaviDyne

TM



5077 Fruitville Rd.; Suite 109

– 157 Sarasota, FL 34234 U.S.A.



Phone 352.275 5319

Page 32/38

6.5 Inspection / Maintenance of the Belt Drive System

The CaviBlaster

®

2040-D is equipped with belt power transmission. The driver

shaft has a manually operated power take-off.

FULL ENGINE SPEED IS REQUIRED FOR PROPER
OPERATION OF THE GUN.

To inspect the belt:

1. Remove the belt guard cover supported by

7

bolts (See Figure 6.2).

2.  If belts need tightening, use the tightening nut to adjust (See Figure 6.2).
3.  Release the bolts holding the pump rails.
4.  Adjust Belt tension.
5.  Tighten pump rail bolts.
6.  Replace belt guard cover.

Figure 6.2

– Inspection / Belt tension.

Belt guard cover
–

7

bolts

Pump belt tension
adjustment nuts (2)

Feed pump
drive belt

«
...
30
31
32
33
34
...
»

Summary of Contents for 2040-D







































Reviews:

No comments

Related manuals for 2040-D

Brand: Caltta Pages: 10

Brand: Generac Power Systems Pages: 16

Hard Gear SGE3500BSi

Brand: DAISHIN Pages: 28

Brand: C. Crane Pages: 13

Brand: Curtis Dyna-Fog Pages: 53

Brand: Jefferson Professional Tools & Equipment Pages: 9

Brand: Panasonic Pages: 22

Brand: Sound Pro Pages: 8

Brand: Denyo Pages: 47

Brand: Denver Pages: 4

Brand: Denver Pages: 43

Brand: Denver Pages: 144

Brand: DuroStar Pages: 66

Brand: Excera Pages: 21

Brand: Excera Pages: 34

Brand: PASCO Pages: 9

Brand: Medion Pages: 194

Brand: Magnasonic Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands