Caviblaster 2040-D Operation & Maintenance Manual Download

Page: 36 / 38

2040-D O&M Manual Ver 3.0 CaviDyne



5077 Fruitville Rd.; Suite 109

– 157 Sarasota, FL 34234 U.S.A.



Phone 352.275 5319

Page 36/38

6. AFTER RELEASING THE MECHANICAL TRIGGER, WATER IS STILL

LEAKING OUT OF THE GUN

- Replace the mechanical trigger valve assembly in the gun handle

7. GUN IS NOT CLEANING PROPERLY

- Verify that the system is operating at the correct pressure (3,700-psi)
- Remove the gun from water with the system at operating pressure and

trigger in the closed or “OFF” position. If water is leaking out of the barrel or
handle, the trigger valve assembly should be replaced.

- Check cavitation and zero-thrust nozzles for foreign particles

Visual inspection
Insert a small wire into nozzle orifices to check for obstruction(s)
Remove trigger valve assembly and “backflush” with compressed air or
pressurized water

This space intentionally left blank

(EOS)

Summary of Contents for 2040-D







































Search results

Summary of Contents for 2040-D

Reviews:

Related manuals for 2040-D

Brands by name

Popular brands

Caviblaster 2040-D, Operation & Maintenance Manual

Search results

Summary of Contents for 2040-D

Reviews:

Related manuals for 2040-D

Brands by name

Popular brands