background image

 

 

2040-D O&M Manual Ver 3.0 CaviDyne

TM

 

 5077 Fruitville Rd.; Suite 109 

– 157 Sarasota, FL 34234 U.S.A. 

 Phone 352.275 5319 

 

 

Page 10/38

 

 

3.0 SAFETY INFORMATION 

 

 
The CaviBlaster

®

 2040-D power unit is an inherently powerful and potentially dangerous 

piece  of  equipment;  however,  with  proper  care  and  training  it  can  be  operated  safely. 
The  2040-D  must  only  be  operated  by  personnel  that  have  read  and  understand  this 
manual.  It  is  intended  to  reinforce  and  review  safety  techniques  to  prevent  personal 
injuries and property damage. 

 

Users  must  comply  with  all  local,  state,  and  national  laws  concerning  high-pressure 
water jetting equipment as well as all underwater work regulations. 
 
It  is  strongly  recommended  that  this  entire  manual  be  reviewed  in-depth  before 
operating  or  servicing  this  equipment.  Service  work  should  only  be  performed  by 
individuals who are proficient in using this equipment. Refer to the applicable section in 
this  manual  for  the  correct  procedures  prior  to  any  installation,  setup,  or  maintenance 
work.  
 

3.1 Personal Safety 

 
Operation of the CaviBlaster

®

 2040-D underwater cleaning system must only be 

attempted by commercial divers or other personnel who have been trained in its 
use.  Appropriate  protective  equipment  should  always  be  worn.  Operation  of  the 
system without the proper equipment and training can result in personal injury.  

 

 

 

CaviDyne

TM

, LLC is not responsible for damages resulting 

from a failure to comply with instructions in this manual. 
Please read carefully before use. 

 

 

If  inspection  or  calibration  of  the  CaviBlaster

®

  gun  is 

being  conducted  out  of  the  water,  remember  that  the 
zero-thrust gun has front and rear jets. Never direct the 
jet  streams  at  a  person  or  animal.  Never  direct  the  jet 
streams  toward  power  lines  or  other  high  voltage 
equipment. 

  

Summary of Contents for 2040-D







































Reviews: