background image

IOM-DA8

16

 

Item No. 

Description

 

 

7  

Diaphragm Cap Screw 

 13 

Piston/Guide 

Bearing

        14  ‡‡ 

Stem Seals

 

  14.1 

Upper Stem Seal

 

  14.2 

Middle Stem Seal

 

  14.3 

Lower Stem Seal

        15  ‡‡ 

Cage Seal

 19 

Cage

 20 

Valve 

Plug

        21  ‡‡ 

Lower Cage Gasket

 

24 

Lower Guide Bushing

        28  ‡‡ 

Seat Disk

 

29 

Seat Disk Washer

 

30 

Seat Disk Nut

‡‡  Recommended Repair Parts

Figure 4:  

Body Sizes

2-1/2" – 4", Composition Diaphragm

The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be con-

strued as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability.  We reserve the right to modify or 

improve the designs or specifications of such product at any time without notice.

Cashco, Inc. does not assume responsibility for the selection, use or maintenance of any product.  Responsibility for proper selection, use and maintenance of any 

Cashco, Inc. product remains solely with the purchaser.

Summary of Contents for DA8



















Reviews: