background image

20

This device complies with RSS-210 of Industry Canada.  Operation is subject to the following two conditions: (1) this device may not cause interference, and 

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

1. This device complies with part 15 of the FCC Rules.  Operation is subject to the following two conditions: (1) this device may not cause harmful interfer-

ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are 

designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However there 

is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following 

measures:  Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet 

on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.  Note:  Any changes 

or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.

PRODUCT SPECIFICATIONS

Model Name:

 

 Heritage™II

Model Number:

 

C19xxxK 

ETL Rating:

 

Wet

Motor:

 

XTR200

 30mm

Blade Span:

 

60"

Blade Pitch:

 

14°

No. of Blades:

 

5

Technology: 

4-Speed Pull Chain

Motor  with  Heritage™  Compatible 

Blades

Weight 

(lbs)

Speed*

(rpm)

Airflow* 

(cfm)

Electricity 

Use* 

(watts)

Airflow 

Efficiency* 

(cfm/watt)

A

B

C

D

E

BL-ADK-RA 

(Adirondack Reclaimed Antique)

39

167

7,179

98

74

14.7 15.4 2.9

16

5.6

BL-TPW-WB

(Tropical Wicker Weathered Bronze)

47

155

6,422

97

66

15.3 15.4 2.9

16

5.6

* = At high speed

Summary of Contents for C19xxxK





















Reviews: